Set Pr.340 (Communication startup mode selection) to other than "0".Also, set Pr.79 (Operation mode) to "0", "2", or "6"

You can set both the BCD code and binary code inputs within the range from 0 to 400 Hz.You can set the bias and gain in

The stop-on-contact control becomes invalid when the start command is turned OFF during the stop-on-contact control and

20 ms or less is required to switch the control with the MC signal.

The adapter is not necessary. Only the dedicated cable FR-CB20□ is required.

No, we have no cable 50 cm long. The optional cables 1 m, 3 m, and 5 m long are available. (1 m: FR-CB201, 3 m: FR-CB203

It is considered that conditions including the power supply and noise change whether the parameter unit is connected or

1. When slight imbalance (approximately 5%) is present with the inverter power supply voltage, the inverter input curren

1. Set Pr.162 to "10" (Frequency search at every start).2. You can ignore the setting if the motor excitation current is

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

451-460 of Total 1353

prev 46 / 136page next

CC-Link

Use Pr.542 (Station number). More Details >>
- No：21876
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
CC-Link

Set Pr.340 (Communication startup mode selection) to other than "0".Also, set Pr.79 (Operation mode) to "0", "2", or "6".Powering the inverter on automatical... More Details >>
- No：21903
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
12-bit digital input

You can set both the BCD code and binary code inputs within the range from 0 to 400 Hz.You can set the bias and gain in 0.01 Hz units.For BCD input, when the... More Details >>
- No：21945
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Plug-in Options , FREQROL-A500
Stop-on-contact control of the FR-E700

The stop-on-contact control becomes invalid when the start command is turned OFF during the stop-on-contact control and the machine is decelerated to a stop ... More Details >>
- No：20822
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-E700
Switching time of the FR-A800 control

20 ms or less is required to switch the control with the MC signal. More Details >>
- No：20838
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-A800
FR-PA07

The adapter is not necessary. Only the dedicated cable FR-CB20□ is required. More Details >>
- No：21362
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
FR-PA07

No, we have no cable 50 cm long. The optional cables 1 m, 3 m, and 5 m long are available. (1 m: FR-CB201, 3 m: FR-CB203, 5 m: FR-CB205) More Details >>
- No：21365
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Rotations per minute vary

It is considered that conditions including the power supply and noise change whether the parameter unit is connected or disconnected, influencing the analog ... More Details >>
- No：21454
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-V200
Current value on input side and output side

1. When slight imbalance (approximately 5%) is present with the inverter power supply voltage, the inverter input current can get imbalanced significantly. I... More Details >>
- No：21476
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-A200
Coasting

1. Set Pr.162 to "10" (Frequency search at every start).2. You can ignore the setting if the motor excitation current is unknown. More Details >>
- No：21718
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

451-460 of Total 1353

Inquiries

page top