In general, relationship between T (torque), K (constant), V (voltage), I (current), and F (frequency) is expressed as "

Torque is not guaranteed for slower than 0.5 Hz. Therefore, no data for this is published. Also, no torque is generated

Connect the high power factor converter and inverter directly with a control cable, without using a relay. Since a fast-

By using the reactors 1 and 2 as well as the outside box supplied with the high power factor converter, while the noise

If all inverters are in regenerative operation, the regenerative power is regenerated to the power supply. If one of the

When the protective function works, the inverter is stopped (output shutoff) by the RDY signal.

If the reactor 1, outside box, and reactor 2 are contained in the same case as the high power factor converter, the unit

The whole system consists of the power supply, molded case circuit breaker, high power factor converter, inverter, and m

To almost "1". (With load factor of 100%)

Only the unit type SC-A□□U has fault output signals. (Terminals Y1 and SD open collector output permissible load 24 VDC

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

461-470 of Total 1368

prev 47 / 137page next

Inverter current characteristics

In general, relationship between T (torque), K (constant), V (voltage), I (current), and F (frequency) is expressed as "T = K × (V/F) × I". Since (V/F) is co... More Details >>
- No：21505
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-V200
Torque characteristic at low speed

Torque is not guaranteed for slower than 0.5 Hz. Therefore, no data for this is published. Also, no torque is generated at 0 Hz. More Details >>
- No：21543
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Control cable between high power factor converter and inverter

Connect the high power factor converter and inverter directly with a control cable, without using a relay. Since a fast-response is required to shut off the ... More Details >>
- No：21555
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Influence on noise level

By using the reactors 1 and 2 as well as the outside box supplied with the high power factor converter, while the noise may increase or decrease depending th... More Details >>
- No：21559
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Regenerative power flow

If all inverters are in regenerative operation, the regenerative power is regenerated to the power supply. If one of the inverters is power driving, the rege... More Details >>
- No：21564
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Protective functions

When the protective function works, the inverter is stopped (output shutoff) by the RDY signal. More Details >>
- No：21570
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Accessories and inverter with built-in high power factor converter

If the reactor 1, outside box, and reactor 2 are contained in the same case as the high power factor converter, the unit becomes larger and heavier while fre... More Details >>
- No：21573
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
System configuration

The whole system consists of the power supply, molded case circuit breaker, high power factor converter, inverter, and motor. The high power factor converter... More Details >>
- No：21575
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Input power factor

To almost "1". (With load factor of 100%) More Details >>
- No：21577
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Fault output signal when inverter trips

Only the unit type SC-A□□U has fault output signals. (Terminals Y1 and SD open collector output permissible load 24 VDC 0.1 A)The box type SC-A□□B indicates ... More Details >>
- No：21580
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , SC-A

461-470 of Total 1368

Inquiries

page top