Check the setting value of Pr.37 (Speed display). When the machine speed is set, Pr.811 is disabled. Change the setting

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur wh

When the second torque limit is used, the settings of Pr.816 and 817 are valid.

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring.

It is not possible when the speed command is communication.

It is not possible under the dancer control. When the negative data is written, it is handled as the positive data in op

Yes. The model is FR-E710W. The input is single-phase 100 V, but the output is three-phase 200 V.

For frequency setting, multi-speed setting is prioritized over current input. Therefore, when the multi-speed signal is

Your suggested use is not recommended due to the following reasons: Output voltage of the 400 V inverter contains "micro

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

41-50 of Total 1368

prev 5 / 137page next

Setting resolution switching

Check the setting value of Pr.37 (Speed display). When the machine speed is set, Pr.811 is disabled. Change the setting to the rotation speed. More Details >>
- No：21161
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700
Slip compensation

Yes, it is. More Details >>
- No：21213
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
IPM motor drive

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur when the load inertia is too high. As a... More Details >>
- No：21216
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Torque limit

When the second torque limit is used, the settings of Pr.816 and 817 are valid. More Details >>
- No：21218
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
LED blinking under encoder feedback control

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring. More Details >>
- No：21220
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Speed command by CC-Link communication

It is not possible when the speed command is communication. More Details >>
- No：21232
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Dancer control during CC-Link communication

It is not possible under the dancer control. When the negative data is written, it is handled as the positive data in operation. Example) When Pr.541 is set ... More Details >>
- No：21243
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
FR-E710W

Yes. The model is FR-E710W. The input is single-phase 100 V, but the output is three-phase 200 V. More Details >>
- No：21320
- Release Date：2018/08/22 16:27
- Category： FREQROL-E700
Priority of multi-speed setting and frequency setting signals

For frequency setting, multi-speed setting is prioritized over current input. Therefore, when the multi-speed signal is input, the inverter switch to multi-s... More Details >>
- No：21400
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Driving 200 V motor by 400 V inverter

Your suggested use is not recommended due to the following reasons: Output voltage of the 400 V inverter contains "micro surge". Usually this surge voltage i... More Details >>
- No：21403
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500

41-50 of Total 1368

Inquiries

page top