You can perform forward and reverse operations with the RUN key on the operation panel by setting Pr.40 (RUN key rotatio

We do not offer a sample program for the programmable controller. Refer to the Instruction Manual and create the program

It is considered that conditions including the power supply and noise change whether the parameter unit is connected or

- SU signal (up to frequency signal)This signal is output when the inverter output frequency reaches the set frequency (

1. When the inverter power supply is turned OFF, the inverter is disconnected from the CC-Link network. However, since t

Since the operation panel and PU connector cannot be specified for command source at the same time, they cannot be used

The inverter restart operation is disabled at turn-OFF of the CS signal while a value other than "9999" (with restart) i

The station number and baud rate were set using the dial for the FR-A5NC, but parameter is used for the FR-A7NC. Pr.542

It is available if the option FR-A8TAT (Control circuit terminal block intercompatibility attachment) is installed. (Som

The ON level is the power supply voltage -3 V or higher and the OFF level is 3 V or lower.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

491-500 of Total 1368

prev 50 / 137page next

Parameter setting

You can perform forward and reverse operations with the RUN key on the operation panel by setting Pr.40 (RUN key rotation direction selection). More Details >>
- No：21719
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ
Do you have a sample program for 485 communication?

We do not offer a sample program for the programmable controller. Refer to the Instruction Manual and create the program by yourself. More Details >>
- No：21522
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Others , FREQROL-E500
Rotations per minute vary

It is considered that conditions including the power supply and noise change whether the parameter unit is connected or disconnected, influencing the analog ... More Details >>
- No：21454
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-V200
Difference between SU (up to frequency) and FU (frequency detection)

- SU signal (up to frequency signal)This signal is output when the inverter output frequency reaches the set frequency (the frequency the inverter is require... More Details >>
- No：21436
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Countermeasures when input power supply is turned off upon equipment fault

1. When the inverter power supply is turned OFF, the inverter is disconnected from the CC-Link network. However, since the CC-Link master station has the aut... More Details >>
- No：21390
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Operation panel and FR-PA07

Since the operation panel and PU connector cannot be specified for command source at the same time, they cannot be used together. More Details >>
- No：21349
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ
Automatic restart after instantaneous power failure

The inverter restart operation is disabled at turn-OFF of the CS signal while a value other than "9999" (with restart) is set in Pr.57. The terminals CS and ... More Details >>
- No：21255
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Replacement

The station number and baud rate were set using the dial for the FR-A5NC, but parameter is used for the FR-A7NC. Pr.542 (Communication station number (CC-Lin... More Details >>
- No：21248
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Control terminal block

It is available if the option FR-A8TAT (Control circuit terminal block intercompatibility attachment) is installed. (Some functions have restrictions. For th... More Details >>
- No：21087
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options , FREQROL-A800 , FREQROL-F800
FR-A8AP

The ON level is the power supply voltage -3 V or higher and the OFF level is 3 V or lower. More Details >>
- No：21002
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , Plug-in Options

491-500 of Total 1368

Inquiries

page top