It is available if the option FR-A8TAT (Control circuit terminal block intercompatibility attachment) is installed. (Som

It is considered to be caused by inverter PWM control. It can be suppressed by raising the PWM carrier frequency (Pr.72)

Set Pr.52 (DU/PU main display data selection) to "100".Displaying the setting frequency while the inverter is stopped an

Since the external thermal prevents the motor from being overheated, install it between the output terminal of the inver

1. You can reset the inverter from an external terminal.You can do it without regard to the setting of Pr.338 (Communica

1. To perform emergency stop, it is recommended to have the motor coast and stop it using a mechanical brake.In this cas

Since the SF-PR is more efficient compared to the SF-JR, the resistance will decrease and the load current will increase

The setting is enabled at the Y24 start-up. The frequency cannot be changed when Y24 is always ON. Turn ON Y24 when writ

Turn ON and OFF the RES signal to enable the inverter-driven operation.

The station number and baud rate were set using the dial for the FR-A5NC, but parameter is used for the FR-A7NC. Pr.542

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

541-550 of Total 1353

prev 55 / 136page next

Control terminal block

It is available if the option FR-A8TAT (Control circuit terminal block intercompatibility attachment) is installed. (Some functions have restrictions. For th... More Details >>
- No：21087
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options , FREQROL-A800 , FREQROL-F800
Noise from motor at low speed

It is considered to be caused by inverter PWM control. It can be suppressed by raising the PWM carrier frequency (Pr.72), but the entire noise and leakage cu... More Details >>
- No：21428
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Setting frequency

Set Pr.52 (DU/PU main display data selection) to "100".Displaying the setting frequency while the inverter is stopped and the output frequency while it is op... More Details >>
- No：21783
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
External installationRated current

Since the external thermal prevents the motor from being overheated, install it between the output terminal of the inverter and the motor.The rated current i... More Details >>
- No：21817
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
CC-Link

1. You can reset the inverter from an external terminal.You can do it without regard to the setting of Pr.338 (Communication operation command source) and Pr... More Details >>
- No：21837
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Inverter general matters

1. To perform emergency stop, it is recommended to have the motor coast and stop it using a mechanical brake.In this case, the output stop (MRS) signal is in... More Details >>
- No：22103
- Release Date：2018/08/22 16:31
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Replacement of the SF-JR with the SF-PR

Since the SF-PR is more efficient compared to the SF-JR, the resistance will decrease and the load current will increase. Check the following two points when... More Details >>
- No：20949
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Others
PLC function

The setting is enabled at the Y24 start-up. The frequency cannot be changed when Y24 is always ON. Turn ON Y24 when writing a frequency. More Details >>
- No：21048
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , FREQROL-F800
Electronic bypass function

Turn ON and OFF the RES signal to enable the inverter-driven operation. More Details >>
- No：21190
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Replacement

The station number and baud rate were set using the dial for the FR-A5NC, but parameter is used for the FR-A7NC. Pr.542 (Communication station number (CC-Lin... More Details >>
- No：21248
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P

541-550 of Total 1353

Inquiries

page top