It is not possible to generate torque larger than the maximum possible torque of the motor by increasing the inverter's

Since the inverter's fault contact is an NC contact, it does not open unless a fault occurs.Therefore, when the control

To supply power via R1 and S1, 60 VA or higher is necessary for 22K or lower and 80 VA or higher is necessary for 30K to

The operation panel of the FR-S500 is not detachable.For the FR-S500-○○K-R (compatible with RS-485 communication), you c

1. By changing RWw1 while RYD is ON, you can change the inverter's frequency.You cannot do this with RYE. You need to tu

1. The braking torque can be considered 50% of the motor rated torque.2. The largest stress the DC injection brake gives

1. If the start signal is present when the power and communication restore, the inverter starts operation. 2. Similarly

“off” is shown in th

Operation mode for manufacturer setting is enabled. For MR-J4-B, MR-J4W2-B and MR-J4W3-B, turning "ON (up)" all the cont

We have the English version of capacity selection software available. For details, contact your local sales office.

You can download the instruction manual from the Mitsubishi Electric FA Global Website. Visit the Mitsubishi Electric F

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

561-570 of Total 1353

prev 57 / 136page next

Two-rank up maximum short-time torque

It is not possible to generate torque larger than the maximum possible torque of the motor by increasing the inverter's capacity.Even when the inverter is up... More Details >>
- No：22027
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Fault contact when connecting separate power supply for each control circuit

Since the inverter's fault contact is an NC contact, it does not open unless a fault occurs.Therefore, when the control power supply (and main circuit power ... More Details >>
- No：22035
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Inverter control power supply

To supply power via R1 and S1, 60 VA or higher is necessary for 22K or lower and 80 VA or higher is necessary for 30K to 55K.Note that the rush current of ap... More Details >>
- No：22043
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Separation of operation panel

The operation panel of the FR-S500 is not detachable.For the FR-S500-○○K-R (compatible with RS-485 communication), you can install the FR-PU04 on the enclosu... More Details >>
- No：22058
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-S500
Operation with CC-Link

1. By changing RWw1 while RYD is ON, you can change the inverter's frequency.You cannot do this with RYE. You need to turn OFF and then ON RYE each time you ... More Details >>
- No：22083
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
DC injection brake

1. The braking torque can be considered 50% of the motor rated torque.2. The largest stress the DC injection brake gives to the motor is the motor heat gener... More Details >>
- No：22088
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Instantaneous power failure of facilities

1. If the start signal is present when the power and communication restore, the inverter starts operation. 2. Similarly to the above, if the start signal is ... More Details >>
- No：22093
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500
“off” is shown in the display.

Operation mode for manufacturer setting is enabled. For MR-J4-B, MR-J4W2-B and MR-J4W3-B, turning "ON (up)" all the control axis setting switches (SW2) enabl... More Details >>
- No：23625
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4
English version of capacity selection software

We have the English version of capacity selection software available. For details, contact your local sales office. More Details >>
- No：23642
- Release Date：2018/09/14 15:10
- Category： Servo Support Software
Instruction manual of capacity selection software

You can download the instruction manual from the Mitsubishi Electric FA Global Website. Visit the Mitsubishi Electric FA Global Website and go to [Download]... More Details >>
- No：23643
- Release Date：2018/09/14 15:10
- Category： Servo Support Software

561-570 of Total 1353

Inquiries

page top