Yes. When Pr.9 = 0, turning is performed with the inverter rated current. Always set the rated motor current.

A tension sensor such as a dancer roll is required for speed control. Because an actual line speed input is required for

The tension controller is suitable for the equipment with low speed and small capacity. The tension controller is suitab

Inverters with the components fixed on the circuit board with an adhesive, an countermeasure against the connector faili

An earth plate permanently installed in the 700 series is included as an option for the 800 series because of the change

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur wh

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring.

Normally, the required space for A700 3.7K or lower is 1 cm. However, when using CC-Link IE, it needs to be separated fo

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

51-60 of Total 1354

prev 6 / 136page next

FR-A800

Yes. When Pr.9 = 0, turning is performed with the inverter rated current. Always set the rated motor current. More Details >>
- No：20897
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL
FR-A800-R2R

A tension sensor such as a dancer roll is required for speed control. Because an actual line speed input is required for the winding diameter calculation by ... More Details >>
- No：20926
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800
FR-A800-R2R

The tension controller is suitable for the equipment with low speed and small capacity. The tension controller is suitable for the equipment with low speed a... More Details >>
- No：20929
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
FR-A800-CRN

Inverters with the components fixed on the circuit board with an adhesive, an countermeasure against the connector failing, or the cables tied (fixed) togeth... More Details >>
- No：20931
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
FR Configurator2

Yes. More Details >>
- No：21008
- Release Date：2018/08/22 16:25
- Category： Engineering Software
Included earth plate

An earth plate permanently installed in the 700 series is included as an option for the 800 series because of the change of the shape of the circuit board. More Details >>
- No：21035
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
Carrier frequency

It is fixed to 5 kHz. More Details >>
- No：21211
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
IPM motor drive

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur when the load inertia is too high. As a... More Details >>
- No：21216
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
LED blinking under encoder feedback control

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring. More Details >>
- No：21220
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Inverter installation when using the FR-A7NCE

Normally, the required space for A700 3.7K or lower is 1 cm. However, when using CC-Link IE, it needs to be separated for 5 cm or more to pass the cable. More Details >>
- No：21227
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

51-60 of Total 1354

Inquiries

page top