No, it does not run. "Err" is displayed when it is operated. Always input the same voltage (400 V) to the main power sup

The ferrule terminal or single wire can be used for the control circuit wiring.

It can be driven by connecting single-phase 200 V to the terminals R and S. In this case, the load current must be one-t

The USB connection requires FR Configurator (FR-SW3-SETUP-WJ) prepared by Mitsubishi Electric Corporation.

The operation panel FR-PA02 requires the optional FR-E5P (control panel rear cover and adapter set) and connection cable

To conform to the EMC Directive when exporting to an EU country, install the filter that conforms to the EMC Directive o

Although you can connect an analog or digital indicator to the terminal FM, use an analog indicator since the wiring len

The potentiometer on the operation panel is initially calibrated so that the maximum indication is slightly over 60 Hz w

When the heat sink is outside, since the heat sink and fan are not waterproof, you need to enclose them so that they are

Grounding can often get dirty due to influence from the inverter main circuit switching. Therefore, when the potentiomet

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

591-600 of Total 1353

prev 60 / 136page next

400 V inverter

No, it does not run. "Err" is displayed when it is operated. Always input the same voltage (400 V) to the main power supply and control power supply. More Details >>
- No：21179
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Wiring and terminal

The ferrule terminal or single wire can be used for the control circuit wiring. More Details >>
- No：21275
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700
Specifications

It can be driven by connecting single-phase 200 V to the terminals R and S. In this case, the load current must be one-third or less of the inverter rated cu... More Details >>
- No：21282
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700
USB connector

The USB connection requires FR Configurator (FR-SW3-SETUP-WJ) prepared by Mitsubishi Electric Corporation. More Details >>
- No：21318
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
FR-PA02

The operation panel FR-PA02 requires the optional FR-E5P (control panel rear cover and adapter set) and connection cable FR-CB20□. Check that Pr.146 (Built-i... More Details >>
- No：21367
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ
EMC countermeasure

To conform to the EMC Directive when exporting to an EU country, install the filter that conforms to the EMC Directive on the inverter, and take measures acc... More Details >>
- No：21414
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Long wire to terminal FM

Although you can connect an analog or digital indicator to the terminal FM, use an analog indicator since the wiring length is long. (The maximum wiring leng... More Details >>
- No：21415
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Indication of potentiometer on operation panel

The potentiometer on the operation panel is initially calibrated so that the maximum indication is slightly over 60 Hz with the potentiometer turned to the m... More Details >>
- No：21427
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
FR-A5CN

When the heat sink is outside, since the heat sink and fan are not waterproof, you need to enclose them so that they are not exposed to the spray of water. More Details >>
- No：21435
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Options
Shielded wiring of external speed setting potentiometer

Grounding can often get dirty due to influence from the inverter main circuit switching. Therefore, when the potentiometer shielded wire is connected to the ... More Details >>
- No：21455
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL

591-600 of Total 1353

Inquiries

page top