The same EDS files cannot be used for the different models. Download the EDS files for F800 from the following page of M

Because RSO (converter reset) of the HC2 is connected to RES of the inverter, the inverter is reset along with the HC2 r

You can install the operation panel FR-DU04 (or parameter unit FR-PU04) on the enclosure surface by connecting it with t

Take the following countermeasure:1. If the thermal trips in low-speed operation, trips can be avoided, depending on the

If the cable length is longer than 100 m, speed may not be read correctly due to voltage drop and waveform deformation o

1. The BU brake unit does not have the fault output.Multiple BU brake units can be connected in parallel.2. Power supply

A reference sine wave signal is generated inside the high power factor converter, and transistors are configured and PWM

Energy saving is achieved by switching from the commercial power supply to the inverter to operate the motor. When the

You can connect them in parallel. Connect the voltmeters in parallel, paying attention to the following: - The output cu

Keep a clearance of "minimum 10cm each on top and bottom and minimum 5cm each on right and left".

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

591-600 of Total 1368

prev 60 / 137page next

FR-A8ND

The same EDS files cannot be used for the different models. Download the EDS files for F800 from the following page of Mitsubishi Electric FA Global Website ... More Details >>
- No：20955
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Plug-in Options
FR-HC2

Because RSO (converter reset) of the HC2 is connected to RES of the inverter, the inverter is reset along with the HC2 reset. (Refer to the wiring diagram in... More Details >>
- No：20948
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options
Installing parameter unit outside control panel

You can install the operation panel FR-DU04 (or parameter unit FR-PU04) on the enclosure surface by connecting it with the inverter via a cable.To do this, d... More Details >>
- No：22044
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
External thermal overheat

Take the following countermeasure:1. If the thermal trips in low-speed operation, trips can be avoided, depending on the external thermal relay operation cha... More Details >>
- No：21954
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500
Encoder cable length restriction

If the cable length is longer than 100 m, speed may not be read correctly due to voltage drop and waveform deformation of the encoder signal. Therefore, use ... More Details >>
- No：21932
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-V200
Brake unit selection

1. The BU brake unit does not have the fault output.Multiple BU brake units can be connected in parallel.2. Power supply voltage 480 V- What resistance value... More Details >>
- No：21930
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
Waveform improvement

A reference sine wave signal is generated inside the high power factor converter, and transistors are configured and PWM switching is performed in the conver... More Details >>
- No：21574
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Energy saving and power supply capacity of inverter

Energy saving is achieved by switching from the commercial power supply to the inverter to operate the motor. When the inverter reduces motor speed, it also... More Details >>
- No：21498
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Others
Connecting voltmeter to terminal AM

You can connect them in parallel. Connect the voltmeters in parallel, paying attention to the following: - The output current should not exceed the permissib... More Details >>
- No：21464
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
FR-CVL

Keep a clearance of "minimum 10cm each on top and bottom and minimum 5cm each on right and left". More Details >>
- No：21178
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Options

591-600 of Total 1368

Inquiries

page top