Refer to the following points.For fan pump -> Square torqueFor general-purpose machine (for example, transport, eleva

The specifications of the FR-V200E series do not allow for choosing from "Reset input always enabled" and "Reset input e

To change the running frequency while the frequency command is input to the terminal 2, adjust the parameters in the fol

You can use the following two methods:1. Turn ON MRS at the same time when STF turns OFF.2. Set Pr.10 = 60 Hz, Pr.11 = 0

1. Yes. The inverter cannot restart if STF and STR are turned OFF.However, on the next startup, the inverter detects coa

Check if any device is connected to the inverter's external terminal.In particular, check if MRS and SD are short-circui

It is not recommended to install a contactor on the input side and connect the auxiliary contact to the terminal STF of

Perform calculation given in the harmonic suppression guidelines, and if the limit value is exceeded, you may also need

The inverter alarm "OV3" occurs when the main circuit DC voltage inside the inverter goes higher than the preset value d

When the programmable controller power is turned OFF while the inverter is in the PLC link operation mode, a communicati

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

621-630 of Total 1368

prev 63 / 137page next

Selection

Refer to the following points.For fan pump -> Square torqueFor general-purpose machine (for example, transport, elevation) -> Constant-torque type More Details >>
- No：22048
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Reset selection

The specifications of the FR-V200E series do not allow for choosing from "Reset input always enabled" and "Reset input enabled only when the protective funct... More Details >>
- No：22031
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-V200
Changing main speed at analog signal input

To change the running frequency while the frequency command is input to the terminal 2, adjust the parameters in the following steps:1. Change Pr.77 to "2".2... More Details >>
- No：22025
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
How can I have the motor coast to stop?

You can use the following two methods:1. Turn ON MRS at the same time when STF turns OFF.2. Set Pr.10 = 60 Hz, Pr.11 = 0 sec, and Pr.12 = 0% (when the invert... More Details >>
- No：21967
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Automatic restart after instantaneous power failure

1. Yes. The inverter cannot restart if STF and STR are turned OFF.However, on the next startup, the inverter detects coasting and restarts.2. When automatic ... More Details >>
- No：21942
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-V200
Auto tuning

Check if any device is connected to the inverter's external terminal.In particular, check if MRS and SD are short-circuited.If they are short-circuited, open... More Details >>
- No：21753
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Installing contactor on input side

It is not recommended to install a contactor on the input side and connect the auxiliary contact to the terminal STF of the inverter for the following reason... More Details >>
- No：21533
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL
Countermeasure against harmonics

Perform calculation given in the harmonic suppression guidelines, and if the limit value is exceeded, you may also need to insert the ACL. Note that you cann... More Details >>
- No：21465
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Options
Countermeasure against error

The inverter alarm "OV3" occurs when the main circuit DC voltage inside the inverter goes higher than the preset value due to the regenerative power returned... More Details >>
- No：21438
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A024
Resetting inverter after restoring from power failure

When the programmable controller power is turned OFF while the inverter is in the PLC link operation mode, a communication error occurs and the inverter trip... More Details >>
- No：21417
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Plug-in Options , FREQROL-A500

621-630 of Total 1368

Inquiries

page top