When running the inverter after auto tuning, the frequency setting value is increased by the amount of the motor slippag

The start commands cannot be input from both sources simultaneously because the operation command source is specified.Yo

1. No parameter setting is required.2. Do not remove the jumpers.

Add an analog output by the FR-A5AY.Monitor the three output; output AM (0 to 5 (10) V) and optional 4 to 20 mA, and 0 t

The low-voltage manual contactor is intended to prevent electric shock during inspection and maintenance of the drive un

You cannot use the FR-PU04 with the FR-HC.

The operation panel of the FR-S500 is not detachable.For the FR-S500-○○K-R (compatible with RS-485 communication), you c

The reset signal does not damage the inverter.It seems that the inverter went faulty due to other reasons.Mitsubishi Ele

1. To perform emergency stop, it is recommended to have the motor coast and stop it using a mechanical brake.In this cas

The system is probably malfunctioning and is in dangerous condition. Do not use it. For repair, contact your local sales

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

631-640 of Total 1353

prev 64 / 136page next

Output frequency monitor value

When running the inverter after auto tuning, the frequency setting value is increased by the amount of the motor slippage, resulting in a higher monitor valu... More Details >>
- No：21781
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
CC-Link

The start commands cannot be input from both sources simultaneously because the operation command source is specified.You can switch the command source as ne... More Details >>
- No：21828
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Brake unit

1. No parameter setting is required.2. Do not remove the jumpers. More Details >>
- No：21927
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
Concurrent monitoring of running frequency, output voltage, and output current

Add an analog output by the FR-A5AY.Monitor the three output; output AM (0 to 5 (10) V) and optional 4 to 20 mA, and 0 to 5 (10) V. More Details >>
- No：21959
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-F500
Manual contactor on output side of drive unit

The low-voltage manual contactor is intended to prevent electric shock during inspection and maintenance of the drive unit.The MELIPM series motor is a synch... More Details >>
- No：21996
- Release Date：2018/08/22 16:30
- Category： Magnet motor drive
Availability of parameter unit

You cannot use the FR-PU04 with the FR-HC. More Details >>
- No：22005
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
Separation of operation panel

The operation panel of the FR-S500 is not detachable.For the FR-S500-○○K-R (compatible with RS-485 communication), you can install the FR-PU04 on the enclosu... More Details >>
- No：22058
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-S500
Reset command during operation

The reset signal does not damage the inverter.It seems that the inverter went faulty due to other reasons.Mitsubishi Electric FA Center can inspect the inver... More Details >>
- No：22065
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Inverter general matters

1. To perform emergency stop, it is recommended to have the motor coast and stop it using a mechanical brake.In this case, the output stop (MRS) signal is in... More Details >>
- No：22103
- Release Date：2018/08/22 16:31
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Wrong connection of servo amplifier power supply

The system is probably malfunctioning and is in dangerous condition. Do not use it. For repair, contact your local sales office. More Details >>
- No：23623
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4 , MELSERVO-JE

631-640 of Total 1353

Inquiries

page top