Reference of proper use of each series is as follows: - A024: When balance between size, performance, and cost is import

It cannot be combined with the power factor improving reactor. (Since the power factor is further improved by the high p

It can be performed by setting Pr.292 (Automatic acceleration/deceleration) to "8" and Pr.279 (Brake opening current) to

Yes, it does. (There are some restrictions.

Yes, the current response is also improved at the same rate.

No, it cannot. Purchase IQ-Works2 or FR Configurator2. Upgrading to from IQ-Works to IQ-Works2 is for a fee.

To change the running frequency while the frequency command is input to the terminal 2, adjust the parameters in the fol

The NC contact does not open when the power supply is cut off whether the inverter is operating or ceased.When the input

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are

When using the geared motor GM-S(B), set Pr.71 to "13" and also set Pr.9, Pr.80, and Pr.81.Perform auto tuning as requir

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

631-640 of Total 1353

prev 64 / 136page next

Difference in purpose from FR-A200 series

Reference of proper use of each series is as follows: - A024: When balance between size, performance, and cost is important. - A200: When system configuratio... More Details >>
- No：21610
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A024
Combination with power factor improving reactor

It cannot be combined with the power factor improving reactor. (Since the power factor is further improved by the high power factor converter, it is not requ... More Details >>
- No：21560
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Brake sequence function

It can be performed by setting Pr.292 (Automatic acceleration/deceleration) to "8" and Pr.279 (Brake opening current) to 0%. More Details >>
- No：21186
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
FR-A8TAT

Yes, it does. (There are some restrictions. More Details >>
- No：21082
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options , FREQROL-A800
FR-A800

Yes, the current response is also improved at the same rate. More Details >>
- No：21079
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800
FR Configurator2

No, it cannot. Purchase IQ-Works2 or FR Configurator2. Upgrading to from IQ-Works to IQ-Works2 is for a fee. More Details >>
- No：20829
- Release Date：2018/08/22 16:24
- Category： Engineering Software
Changing main speed at analog signal input

To change the running frequency while the frequency command is input to the terminal 2, adjust the parameters in the following steps:1. Change Pr.77 to "2".2... More Details >>
- No：22025
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Fault contact state when input side power supply is cut off

The NC contact does not open when the power supply is cut off whether the inverter is operating or ceased.When the input side power supply is cut off, the DC... More Details >>
- No：21958
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-S500
NET mode

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are setting the operation upon power-on.... More Details >>
- No：21759
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Advanced magnetic flux vector control

When using the geared motor GM-S(B), set Pr.71 to "13" and also set Pr.9, Pr.80, and Pr.81.Perform auto tuning as required. Perform auto tuning as required. ... More Details >>
- No：21756
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700

631-640 of Total 1353

Inquiries

page top