The output torque characteristics of the FREQROL-E500 series are shown in the figure below. Figure 1

To use an inverter using the external contact coast to stop (to shut off the inverter's output), short-circuit the termi

Since the FR-A540-0.75K has a brake transistor for resistor regenerative driving inside the inverter, you do not need to

Take the following countermeasure:1. If the thermal trips in low-speed operation, trips can be avoided, depending on the

When running the inverter after auto tuning, the frequency setting value is increased by the amount of the motor slippag

Check if any device is connected to the inverter's external terminal.In particular, check if MRS and SD are short-circui

Yes, but functions are partially limited. (The FR-PU02 cannot demonstrate its full ability. The FR-PU01 cannot be used.)

You can use the input terminals X1 to X3 for an input terminal function such as 7-speed operation (high, middle, and low

When the carrier frequency increases, noise and leakage current increase accordingly. To prevent the noise and leakage c

Only the unit type SC-A□□U has fault output signals. (Terminals Y1 and SD open collector output permissible load 24 VDC

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

641-650 of Total 1368

prev 65 / 137page next

Relationship between frequency and output torque

The output torque characteristics of the FREQROL-E500 series are shown in the figure below. Figure 1 More Details >>
- No：22024
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500
Coasting operation of the inverter

To use an inverter using the external contact coast to stop (to shut off the inverter's output), short-circuit the terminals MRS and SD.For CC-Link operation... More Details >>
- No：22003
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Brake unit selection

Since the FR-A540-0.75K has a brake transistor for resistor regenerative driving inside the inverter, you do not need to use BU. Just remove the jumper from ... More Details >>
- No：21992
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
External thermal overheat

Take the following countermeasure:1. If the thermal trips in low-speed operation, trips can be avoided, depending on the external thermal relay operation cha... More Details >>
- No：21954
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500
Output frequency monitor value

When running the inverter after auto tuning, the frequency setting value is increased by the amount of the motor slippage, resulting in a higher monitor valu... More Details >>
- No：21781
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Auto tuning

Check if any device is connected to the inverter's external terminal.In particular, check if MRS and SD are short-circuited.If they are short-circuited, open... More Details >>
- No：21753
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Can I use the parameter unit FR-PU02?

Yes, but functions are partially limited. (The FR-PU02 cannot demonstrate its full ability. The FR-PU01 cannot be used.) To use the parameter unit FR-PU02, u... More Details >>
- No：21613
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A024
Input terminal function selection of multi-function series

You can use the input terminals X1 to X3 for an input terminal function such as 7-speed operation (high, middle, and low speed), output stop during motor ope... More Details >>
- No：21601
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-U100
Noise and leakage current (tone modulation control) of low-noise series

When the carrier frequency increases, noise and leakage current increase accordingly. To prevent the noise and leakage current from increasing while keeping ... More Details >>
- No：21599
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-U100
Fault output signal when inverter trips

Only the unit type SC-A□□U has fault output signals. (Terminals Y1 and SD open collector output permissible load 24 VDC 0.1 A)The box type SC-A□□B indicates ... More Details >>
- No：21580
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , SC-A

641-650 of Total 1368

Inquiries

page top