If the command is 0.01 Hz or higher, the positioning control is performed.

The error may occur if the old version of GX-WORKS3 is used. Update GX-WORKS3 to the latest version.

No, it cannot. The standard operation panel (FR-DU08) can be connected to the face of the board by using the FR-ADP (ope

It is not possible because the RS-485 terminal block is not installed. Use the FR-A800 (RS-485 communication type) when

The communication via the MELSECNET is not available.

When exporting geared motors to China, for 0.75 to 375kW or less they are subject to high-efficiency standards regardles

By either of following methods: (MR-J4) 1. On MR Configurator2, select [Diagnosis] - [Alarm Display] - [Clear]. 2. Set

1. By changing RWw1 while RYD is ON, you can change the inverter's frequency.You cannot do this with RYE. You need to tu

The inverter's output voltage is controlled by switching DC voltage and has a pulse voltage waveform.(It is not a clean

To change the running frequency while the frequency command is input to the terminal 2, adjust the parameters in the fol

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

651-660 of Total 1368

prev 66 / 137page next

MM-FR-A800

If the command is 0.01 Hz or higher, the positioning control is performed. More Details >>
- No：21001
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800
FR Configurator2 (trial version)

The error may occur if the old version of GX-WORKS3 is used. Update GX-WORKS3 to the latest version. More Details >>
- No：20971
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Engineering Software
FR-PA07

No, it cannot. The standard operation panel (FR-DU08) can be connected to the face of the board by using the FR-ADP (operation panel connection connector) an... More Details >>
- No：20898
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Options , FREQROL-A800 , FREQROL-F800
FR-A800-E

It is not possible because the RS-485 terminal block is not installed. Use the FR-A800 (RS-485 communication type) when performing the RS-485 communication. More Details >>
- No：20881
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-A800 , FREQROL-F800
Seamless communication of FR Configurator SW3

The communication via the MELSECNET is not available. More Details >>
- No：20830
- Release Date：2018/08/22 16:24
- Category： Engineering Software
About cautions when shipping geared motors to China

When exporting geared motors to China, for 0.75 to 375kWor less they are subject to high-efficiency standards regardless of whether they are shipped on their... More Details >>
- No：20766
- Release Date：2018/08/21 16:10
- Update：2018/09/04 16:11
- Category： Geared Motors Parallel shaft type , Geared Motors Right angle shaft type
Clearing the alarm history

By either of following methods: (MR-J4) 1. On MR Configurator2, select [Diagnosis] - [Alarm Display] - [Clear]. 2. Set alarm history clear of parameter to "... More Details >>
- No：23650
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4
Operation with CC-Link

1. By changing RWw1 while RYD is ON, you can change the inverter's frequency.You cannot do this with RYE. You need to turn OFF and then ON RYE each time you ... More Details >>
- No：22083
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Output voltage measurement

The inverter's output voltage is controlled by switching DC voltage and has a pulse voltage waveform.(It is not a clean sine wave.)Therefore, it cannot be me... More Details >>
- No：22029
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Changing main speed at analog signal input

To change the running frequency while the frequency command is input to the terminal 2, adjust the parameters in the following steps:1. Change Pr.77 to "2".2... More Details >>
- No：22025
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500

651-660 of Total 1368

Inquiries

page top