You can calculate the torque from the power. From the general equation: Pout = ωn × TT = (Pout × τ)/ωnPout: Measured va

Connect the high power factor converter and inverter directly with a control cable, without using a relay. Since a fast-

It cannot be combined with the power factor improving reactor. (Since the power factor is further improved by the high p

Check the parameters listed below necessary for tuning again.Pr.9, Pr.71, Pr.80, Pr.81, Pr.83, Pr.84, and Pr.96

Set Pr.146 (Built-in potentiometer switching) to "0".This allows for using the potentiometer built in the FR-PA02 to set

If you are using analog voltage commands, connect the voltage inputs to the FR-E500 and FR-Z200 in parallel to equalize

Set the parameters below. For other parameters, keep the initial settings.1. Set Pr.122 (Communication check time interv

The inverter's power supply capacity can be calculated using the following equation:Power supply capacity [kVA] = Motor

If you ground the common terminals of the control circuit, it is connected with the inverter's earthing and the inverter

If you are using an external VR, influence by noise is probable.Setting Pr.74 (Input filter time constant) to a higher v

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

661-670 of Total 1353

prev 67 / 136page next

How can I calculate the processing torque from the measured power?

You can calculate the torque from the power. 　From the general equation: Pout = ωn × TT = (Pout × τ)/ωnPout: Measured valueωn: Actual motor shaft angular fre... More Details >>
- No：21475
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Others , FREQROL-A500
Control cable between high power factor converter and inverter

Connect the high power factor converter and inverter directly with a control cable, without using a relay. Since a fast-response is required to shut off the ... More Details >>
- No：21555
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Combination with power factor improving reactor

It cannot be combined with the power factor improving reactor. (Since the power factor is further improved by the high power factor converter, it is not requ... More Details >>
- No：21560
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Tuning

Check the parameters listed below necessary for tuning again.Pr.9, Pr.71, Pr.80, Pr.81, Pr.83, Pr.84, and Pr.96 More Details >>
- No：21726
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Operation panel (FR-PA02)

Set Pr.146 (Built-in potentiometer switching) to "0".This allows for using the potentiometer built in the FR-PA02 to set the frequency.(Set this parameter to... More Details >>
- No：21730
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ
I want to synchronize the Z200 and E500.

If you are using analog voltage commands, connect the voltage inputs to the FR-E500 and FR-Z200 in parallel to equalize inputs to both units and speeds are s... More Details >>
- No：21929
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500 , FREQROL-Z200
Inverter setup

Set the parameters below. For other parameters, keep the initial settings.1.　Set Pr.122 (Communication check time interval) to other than "0". ("9999" is OK.... More Details >>
- No：21986
- Release Date：2018/08/22 16:30
- Category： Engineering Software
Consideration on power supply capacity

The inverter's power supply capacity can be calculated using the following equation:Power supply capacity [kVA] = Motor output (kW)/(Motor efficiency × Inver... More Details >>
- No：22000
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Common terminals of control circuit

If you ground the common terminals of the control circuit, it is connected with the inverter's earthing and the inverter's noise may be input to the control ... More Details >>
- No：22037
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Frequency display deviation

If you are using an external VR, influence by noise is probable.Setting Pr.74 (Input filter time constant) to a higher value stabilizes the frequency command... More Details >>
- No：22061
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500

661-670 of Total 1353

Inquiries

page top