We have no sample program for RS485 communication. Since the communication method of the FR-SW0-SETUP uses a different p

Ensure that the inverter is in the PU operation mode and stopped, change the following parameters: 1. Read Pr.923 (Built

To conform to the EMC Directive when exporting to an EU country, install the filter that conforms to the EMC Directive o

For frequency setting, multi-speed setting is prioritized over current input. Therefore, when the multi-speed signal is

The stop-on-contact control does not function in the combined operation mode. Perform the control in the External opera

Use high-duty brake resistor FR-ABR-2.2K. (Shared with the 1.5K inverter.)

Yes. The model is FR-E710W. The input is single-phase 100 V, but the output is three-phase 200 V.

For the models other than FR-A700/F700, use FR-Configurator (FR-SW3-SETUP-WJ). They are not supported by FR-Configurator

When the built-in brake resistor is used, the regenerative brake duty is as follows:200 V 0.4K to 3.7K: 3%, 5.5K to 7.5K

The corresponding bit (RYB) can be used when a function other than reset is assigned to the RES terminal, but it cannot

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

661-670 of Total 1353

prev 67 / 136page next

Communication operation with FR-E500

We have no sample program for RS485 communication. Since the communication method of the FR-SW0-SETUP uses a different protocol from 485 communication and st... More Details >>
- No：21451
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Frequency setting

Ensure that the inverter is in the PU operation mode and stopped, change the following parameters: 1. Read Pr.923 (Built-in frequency setting potentiometer g... More Details >>
- No：21416
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
EMC countermeasure

To conform to the EMC Directive when exporting to an EU country, install the filter that conforms to the EMC Directive on the inverter, and take measures acc... More Details >>
- No：21414
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Priority of multi-speed setting and frequency setting signals

For frequency setting, multi-speed setting is prioritized over current input. Therefore, when the multi-speed signal is input, the inverter switch to multi-s... More Details >>
- No：21400
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Operation mode setting

The stop-on-contact control does not function in the combined operation mode. 　Perform the control in the External operation mode. More Details >>
- No：21354
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Brake resistor

Use high-duty brake resistor FR-ABR-2.2K. (Shared with the 1.5K inverter.) More Details >>
- No：21330
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
FR-E710W

Yes. The model is FR-E710W. The input is single-phase 100 V, but the output is three-phase 200 V. More Details >>
- No：21320
- Release Date：2018/08/22 16:27
- Category： FREQROL-E700
Supported model for FR-Configurator

For the models other than FR-A700/F700, use FR-Configurator (FR-SW3-SETUP-WJ). They are not supported by FR-Configurator (FR-SW2-SETUP-WJ). When you have the... More Details >>
- No：21313
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Brake resistor

When the built-in brake resistor is used, the regenerative brake duty is as follows:200 V 0.4K to 3.7K: 3%, 5.5K to 7.5K: 2%400 V 0.4K to 7.5K: 2 % The capac... More Details >>
- No：21273
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700
CC-Link

The corresponding bit (RYB) can be used when a function other than reset is assigned to the RES terminal, but it cannot be used as the reset function. Use RY... More Details >>
- No：21142
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Plug-in Options

661-670 of Total 1353

Inquiries

page top