You can use it with the single-phase 200 V input by increasing the speed controller capacity to one-rank higher than the

Since the converter in the high power factor converter section performs PWM switching, the leakage current increases to

Connect the high power factor converter and inverter directly with a control cable, without using a relay. Since a fast-

1. Such a behavior does not usually happen. (1) The operation command (STF) is not input, contact faults are present, o

The internal processing speed is not published. The analog input specifications are as follows: FR-A500???1/4000FR-E500?

This error is displayed when the inverter and operation panel FR-PU04 cannot communicate with each other correctly or th

Torque is not guaranteed for slower than 0.5 Hz. Therefore, no data for this is published. Also, no torque is generated

You can drive the motor with the FR-V240E-5.5K. However, the following conditions apply: - You need to perform auto tuni

1. You cannot use the inverter in an environment where it is exposed to oil mist. You need to enclose the inverter in a

Connection method for the A500 and E500 is shown in the figure below. The figure is given in an Excel file. Figure 1

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

671-680 of Total 1368

prev 68 / 137page next

Can I use it with single-phase 200 V input?

You can use it with the single-phase 200 V input by increasing the speed controller capacity to one-rank higher than the motor capacity. (Output is three-pha... More Details >>
- No：21581
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , SC-A
Influence on leakage current

Since the converter in the high power factor converter section performs PWM switching, the leakage current increases to the same level as the general-purpose... More Details >>
- No：21558
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Control cable between high power factor converter and inverter

Connect the high power factor converter and inverter directly with a control cable, without using a relay. Since a fast-response is required to shut off the ... More Details >>
- No：21555
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Inverter output stop

1. Such a behavior does not usually happen. 　(1) The operation command (STF) is not input, contact faults are present, or wire is broken. 　(2) The output shu... More Details >>
- No：21552
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Analog signal resolution

The internal processing speed is not published. The analog input specifications are as follows: FR-A500???1/4000FR-E500???1/1000MR-H???1/4000 More Details >>
- No：21550
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
"Err" displayed at power-ON

This error is displayed when the inverter and operation panel FR-PU04 cannot communicate with each other correctly or the reset signal remains ON. Therefore,... More Details >>
- No：21546
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Torque characteristic at low speed

Torque is not guaranteed for slower than 0.5 Hz. Therefore, no data for this is published. Also, no torque is generated at 0 Hz. More Details >>
- No：21543
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
I want to drive other manufacturer's motor with PG

You can drive the motor with the FR-V240E-5.5K. However, the following conditions apply: - You need to perform auto tuning because the motor's circuit consta... More Details >>
- No：21539
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-V200
Countermeasure against oil mist

1. You cannot use the inverter in an environment where it is exposed to oil mist. 　You need to enclose the inverter in an enclosure and then install the encl... More Details >>
- No：21538
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Connection with personal computer

Connection method for the A500 and E500 is shown in the figure below. The figure is given in an Excel file. Figure 1 More Details >>
- No：21536
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500

671-680 of Total 1368

Inquiries

page top