"8" display in offline auto tuning means forced stop by the operator. This means that you stopped operation before tunin

Continuous 100% regenerative braking torque is available for the rated capacity of the high power factor converter. (The

The following three functions can be set: - Acceleration/deceleration time- Electronic thermal O/L relay- Maximum freque

The FR-E720S series and D720S series conform to the single-phase 200 V input specifications.

When offline auto tuning ends normally, the setting of this parameter changes to "3".This means that auto tuning complet

With your setting, since Pr.60 assigns the OH function to the terminal PL, and terminals RL and SD are open, an external

The surface temperature of approximately 70?C is OK.The following shows the MM-CF352 frame temperature for reference.(Ac

The contact between the terminals RDY and SE is open collector output.Operation is:Normal: Non-conductiveFault: Conducti

The operation panel of the FR-S500 is not detachable.For the FR-S500-○○K-R (compatible with RS-485 communication), you c

SW1 is not supported because there is no product However, SW2 can be upgraded by entering the product ID.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

681-690 of Total 1353

prev 69 / 136page next

Overcurrent at low speed

"8" display in offline auto tuning means forced stop by the operator. This means that you stopped operation before tuning completes. 　With this forced stop, ... More Details >>
- No：21527
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Regenerative driving capability

Continuous 100% regenerative braking torque is available for the rated capacity of the high power factor converter. (The same braking ability of the FR-A201 ... More Details >>
- No：21563
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
What parameters (settings) are available?

The following three functions can be set: - Acceleration/deceleration time- Electronic thermal O/L relay- Maximum frequencyThe parameter unit is not used but... More Details >>
- No：21584
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , SC-A
Single-phase 200 V input

The FR-E720S series and D720S series conform to the single-phase 200 V input specifications. More Details >>
- No：21723
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700
Auto tuning

When offline auto tuning ends normally, the setting of this parameter changes to "3".This means that auto tuning completed normally.If the setting value is "... More Details >>
- No：21748
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Current input switching operation

With your setting, since Pr.60 assigns the OH function to the terminal PL, and terminals RL and SD are open, an external protection error occurs. (It does no... More Details >>
- No：21975
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-S500
Motor heat generation

The surface temperature of approximately 70?C is OK.The following shows the MM-CF352 frame temperature for reference.(Actual temperature rise depends on how ... More Details >>
- No：21988
- Release Date：2018/08/22 16:30
- Category： Magnet motor drive
Control wire of FR-HC RDY signal

The contact between the terminals RDY and SE is open collector output.Operation is:Normal: Non-conductiveFault: Conductive More Details >>
- No：22017
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
Separation of operation panel

The operation panel of the FR-S500 is not detachable.For the FR-S500-○○K-R (compatible with RS-485 communication), you can install the FR-PU04 on the enclosu... More Details >>
- No：22058
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-S500
SW1DND-FRC2 (FR Configurator2)

SW1 is not supported because there is no product However, SW2 can be upgraded by entering the product ID. More Details >>
- No：21067
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Engineering Software

681-690 of Total 1353

Inquiries

page top