It is possible by using the terminal A to C with the negative logic setting.

Because the multi-speed terminal is disabled, it does not operate in multi-speed.

There is no setting to disable it, but setting a high torque limit level such as 400 % can disable the limit.

Normally, the required space for A700 3.7K or lower is 1 cm. However, when using CC-Link IE, it needs to be separated fo

When the communication error occurs, the input signal status is not retained, and all the bits turn OFF. When the commun

No, it is not changed. Pr.268 is the parameter for the operation panel.

The current value can be displayed on the operation panel without regard to the setting of monitor-related parameters. A

Grounding can often get dirty due to influence from the inverter main circuit switching. Therefore, when the potentiomet

You can connect them in parallel. Connect the voltmeters in parallel, paying attention to the following: - The output cu

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

61-70 of Total 1368

prev 7 / 137page next

ABC terminal

It is possible by using the terminal A to C with the negative logic setting. More Details >>
- No：21203
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Remote setting function

Because the multi-speed terminal is disabled, it does not operate in multi-speed. More Details >>
- No：21205
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Carrier frequency

It is fixed to 5 kHz. More Details >>
- No：21211
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Torque limit

There is no setting to disable it, but setting a high torque limit level such as 400 % can disable the limit. More Details >>
- No：21217
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Inverter installation when using the FR-A7NCE

Normally, the required space for A700 3.7K or lower is 1 cm. However, when using CC-Link IE, it needs to be separated for 5 cm or more to pass the cable. More Details >>
- No：21227
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Remote input signal of CC-Link communication

When the communication error occurs, the input signal status is not retained, and all the bits turn OFF. When the communication establishes again, the bit tu... More Details >>
- No：21237
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Pr.268 (Monitor decimal digits selection) during CC-Link communication

No, it is not changed. Pr.268 is the parameter for the operation panel. More Details >>
- No：21241
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Current value monitor

The current value can be displayed on the operation panel without regard to the setting of monitor-related parameters. As the current value remains 0 A, the ... More Details >>
- No：21405
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Shielded wiring of external speed setting potentiometer

Grounding can often get dirty due to influence from the inverter main circuit switching. Therefore, when the potentiometer shielded wire is connected to the ... More Details >>
- No：21455
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Connecting voltmeter to terminal AM

You can connect them in parallel. Connect the voltmeters in parallel, paying attention to the following: - The output current should not exceed the permissib... More Details >>
- No：21464
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL

61-70 of Total 1368

Inquiries

page top