You can drive the motor with the FR-V240E-5.5K. However, the following conditions apply: - You need to perform auto tuni

Torque is not guaranteed for slower than 0.5 Hz. Therefore, no data for this is published. Also, no torque is generated

This error is displayed when the inverter and operation panel FR-PU04 cannot communicate with each other correctly or th

The internal processing speed is not published. The analog input specifications are as follows: FR-A500???1/4000FR-E500?

1. Such a behavior does not usually happen. (1) The operation command (STF) is not input, contact faults are present, o

Connect the high power factor converter and inverter directly with a control cable, without using a relay. Since a fast-

Since the converter in the high power factor converter section performs PWM switching, the leakage current increases to

You can use it with the single-phase 200 V input by increasing the speed controller capacity to one-rank higher than the

The following three functions can be set: - Acceleration/deceleration time- Electronic thermal O/L relay- Maximum freque

The parameter unit is not available. Use two internal potentiometers to set the electronic thermal O/L relay and acceler

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

691-700 of Total 1368

prev 70 / 137page next

I want to drive other manufacturer's motor with PG

You can drive the motor with the FR-V240E-5.5K. However, the following conditions apply: - You need to perform auto tuning because the motor's circuit consta... More Details >>
- No：21539
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-V200
Torque characteristic at low speed

Torque is not guaranteed for slower than 0.5 Hz. Therefore, no data for this is published. Also, no torque is generated at 0 Hz. More Details >>
- No：21543
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
"Err" displayed at power-ON

This error is displayed when the inverter and operation panel FR-PU04 cannot communicate with each other correctly or the reset signal remains ON. Therefore,... More Details >>
- No：21546
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Analog signal resolution

The internal processing speed is not published. The analog input specifications are as follows: FR-A500???1/4000FR-E500???1/1000MR-H???1/4000 More Details >>
- No：21550
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Inverter output stop

1. Such a behavior does not usually happen. 　(1) The operation command (STF) is not input, contact faults are present, or wire is broken. 　(2) The output shu... More Details >>
- No：21552
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Control cable between high power factor converter and inverter

Connect the high power factor converter and inverter directly with a control cable, without using a relay. Since a fast-response is required to shut off the ... More Details >>
- No：21555
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Influence on leakage current

Since the converter in the high power factor converter section performs PWM switching, the leakage current increases to the same level as the general-purpose... More Details >>
- No：21558
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Can I use it with single-phase 200 V input?

You can use it with the single-phase 200 V input by increasing the speed controller capacity to one-rank higher than the motor capacity. (Output is three-pha... More Details >>
- No：21581
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , SC-A
What parameters (settings) are available?

The following three functions can be set: - Acceleration/deceleration time- Electronic thermal O/L relay- Maximum frequencyThe parameter unit is not used but... More Details >>
- No：21584
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , SC-A
Difference from conventional product (parameter unit)

The parameter unit is not available. Use two internal potentiometers to set the electronic thermal O/L relay and acceleration/deceleration time, and two swit... More Details >>
- No：21585
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , SC-A

691-700 of Total 1368

Inquiries

page top