You can vary the carrier frequency within the range of 0.7 to 14.5 kHz, and it is initially set to 1 kHz that generates

Yes. Compared with the FR-A100:- The PI control function is added.- Fast-response current limit operation is improved.-

Basically it is not possible due to the operation command source.However, if Pr.77 (Parameter write selection) is set to

When using the geared motor GM-S(B), set Pr.71 to "13" and also set Pr.9, Pr.80, and Pr.81.Perform auto tuning as requir

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are

The NC contact does not open when the power supply is cut off whether the inverter is operating or ceased.When the input

To change the running frequency while the frequency command is input to the terminal 2, adjust the parameters in the fol

No, it cannot. Purchase IQ-Works2 or FR Configurator2. Upgrading to from IQ-Works to IQ-Works2 is for a fee.

Yes, the current response is also improved at the same rate.

Yes, it does. (There are some restrictions.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

711-720 of Total 1353

prev 72 / 136page next

Range of carrier frequency

You can vary the carrier frequency within the range of 0.7 to 14.5 kHz, and it is initially set to 1 kHz that generates low noise and leakage current. You ca... More Details >>
- No：21607
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A024
Compatibility of the function with FR-A100

Yes. Compared with the FR-A100:- The PI control function is added.- Fast-response current limit operation is improved.- Cumulative energy monitor is added. More Details >>
- No：21628
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A100
FR-PA07

Basically it is not possible due to the operation command source.However, if Pr.77 (Parameter write selection) is set to "2", you can use both the FR-PA07 an... More Details >>
- No：21698
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ
Advanced magnetic flux vector control

When using the geared motor GM-S(B), set Pr.71 to "13" and also set Pr.9, Pr.80, and Pr.81.Perform auto tuning as required. Perform auto tuning as required. ... More Details >>
- No：21756
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
NET mode

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are setting the operation upon power-on.... More Details >>
- No：21759
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Fault contact state when input side power supply is cut off

The NC contact does not open when the power supply is cut off whether the inverter is operating or ceased.When the input side power supply is cut off, the DC... More Details >>
- No：21958
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-S500
Changing main speed at analog signal input

To change the running frequency while the frequency command is input to the terminal 2, adjust the parameters in the following steps:1. Change Pr.77 to "2".2... More Details >>
- No：22025
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
FR Configurator2

No, it cannot. Purchase IQ-Works2 or FR Configurator2. Upgrading to from IQ-Works to IQ-Works2 is for a fee. More Details >>
- No：20829
- Release Date：2018/08/22 16:24
- Category： Engineering Software
FR-A800

Yes, the current response is also improved at the same rate. More Details >>
- No：21079
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800
FR-A8TAT

Yes, it does. (There are some restrictions. More Details >>
- No：21082
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options , FREQROL-A800

711-720 of Total 1353

Inquiries

page top