1. No parameter setting is required.2. Do not remove the jumpers.

The start commands cannot be input from both sources simultaneously because the operation command source is specified.Yo

When running the inverter after auto tuning, the frequency setting value is increased by the amount of the motor slippag

Up to 6 units. If you connect 7 or more inverters, the permissible output of control signals is exceeded. Be sure to use

Continuous 100% regenerative braking torque is available for the rated capacity of the high power factor converter. (The

"PS" appears when the STOP key on the operation panel is pressed during external operation. It is considered that someon

The standby power of the FR-F700PJ series (with filterpack) is registered in member's page of Mitsubishi Electric FA Glo

The following reasons are possible. - The signal of Z phase does not exist. (It is not returned normally.) - The setting

Yes. However, it is difficult to wind the twisted wires because they are thick.

Position control is available under vector control with an encoder. Under PM sensorless vector control in combination wi

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

721-730 of Total 1353

prev 73 / 136page next

Brake unit

1. No parameter setting is required.2. Do not remove the jumpers. More Details >>
- No：21927
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
CC-Link

The start commands cannot be input from both sources simultaneously because the operation command source is specified.You can switch the command source as ne... More Details >>
- No：21828
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Output frequency monitor value

When running the inverter after auto tuning, the frequency setting value is increased by the amount of the motor slippage, resulting in a higher monitor valu... More Details >>
- No：21781
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Connecting multiple inverters to single high power factor converter

Up to 6 units. If you connect 7 or more inverters, the permissible output of control signals is exceeded. Be sure to use a high power factor converter with t... More Details >>
- No：21566
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Regenerative driving capability

Continuous 100% regenerative braking torque is available for the rated capacity of the high power factor converter. (The same braking ability of the FR-A201 ... More Details >>
- No：21563
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Indication of FR-E520

"PS" appears when the STOP key on the operation panel is pressed during external operation. It is considered that someone pressed the key. Dismiss "PS" in on... More Details >>
- No：21478
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Standby power

The standby power of the FR-F700PJ series (with filterpack) is registered in member's page of Mitsubishi Electric FA Global Website. Refer to the Technical N... More Details >>
- No：21210
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Orientation control

The following reasons are possible. - The signal of Z phase does not exist. (It is not returned normally.) - The setting of Pr.359 encoder rotation direction... More Details >>
- No：21162
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700
Line noise filter

Yes. However, it is difficult to wind the twisted wires because they are thick. More Details >>
- No：21128
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Options
FR-A800

Position control is available under vector control with an encoder. Under PM sensorless vector control in combination with a MM-CF motor, simple positioning ... More Details >>
- No：21105
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800

721-730 of Total 1353

Inquiries

page top