Pr.38 of the E500 corresponds to Pr.125 (Terminal 2 frequency setting gain frequency) of D700. Pr.39 of the E500 corresp

Since the initial value of Pr.13 (Starting frequency) is 0.5 Hz, the operation does not start unless 0.5 Hz or higher fr

Set Pr.79 (Operation mode) to "3" and Pr.161 (Frequency setting/key lock operation selection) to "1".

There is no problem, however, earthing (grounding) from each FG terminal is recommended to avoid the influence of noises

When performing the PID control by CC-Link communication, the X14 signal is disabled.

Only one instruction is executed. The instruction to be executed is not fixed.

No, they are not connected inside the inverter.

Other than "0" can be input. The inverter is reset by writing any numerical value.

It decelerates and stops. The operation is the same as the one when the Bit of forward rotation command and reverse rota

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

751-760 of Total 1368

prev 76 / 137page next

Replacement

Pr.38 of the E500 corresponds to Pr.125 (Terminal 2 frequency setting gain frequency) of D700. Pr.39 of the E500 corresponds to Pr.126 (Terminal 4 frequency ... More Details >>
- No：21254
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-D700
Frequency command

Since the initial value of Pr.13 (Starting frequency) is 0.5 Hz, the operation does not start unless 0.5 Hz or higher frequency is set. When 0.49 Hz is set i... More Details >>
- No：21251
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Operation method

Set Pr.79 (Operation mode) to "3" and Pr.161 (Frequency setting/key lock operation selection) to "1". More Details >>
- No：21249
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Earthing (grounding) of FR-A7NC (E kit)

There is no problem, however, earthing (grounding) from each FG terminal is recommended to avoid the influence of noises. More Details >>
- No：21240
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
PID control of CC-Link communication

When performing the PID control by CC-Link communication, the X14 signal is disabled. More Details >>
- No：21233
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Instruction code execution request of CC-Link communication

Only one instruction is executed. The instruction to be executed is not fixed. More Details >>
- No：21231
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
FR-A7NCE connector

No, they are not connected inside the inverter. More Details >>
- No：21225
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
System environment variable of the Modbus-RTU communication

Other than "0" can be input. The inverter is reset by writing any numerical value. More Details >>
- No：21224
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
System environment variable of the Modbus-RTU communication

It decelerates and stops. The operation is the same as the one when the Bit of forward rotation command and reverse rotation command are turned OFF. More Details >>
- No：21222
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Leakage current

It is 1 mA as the 700 series. More Details >>
- No：21204
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

751-760 of Total 1368

Inquiries

page top