The new function includes:- PI control function- Cumulative energy monitor (monitor accuracy: approximately ±25% of full

If the cable length is longer than 100 m, speed may not be read correctly due to voltage drop and waveform deformation o

The usual inverter input current is determined not by the inverter capacity but by the motor capacity (motor load).There

The inverter does not have a function to limit the current at 0 Hz.Although it has the DC injection brake, it is intende

It is not possible to generate torque larger than the maximum possible torque of the motor by increasing the inverter's

First, ensure that the parameter for automatic restart after instantaneous power failure is set correctly and then do th

Connect the shield to the terminal SD.

The reset signal does not damage the inverter.It seems that the inverter went faulty due to other reasons.Mitsubishi Ele

1. Pr.1 and 18 limit the output to 120 Hz. Use Pr.18 to change the maximum frequency. 2. If you want to output the binar

When the rotary switch is “0”, the 1st axis and is “1”, the 2nd axis. When the rotary switch is “A”, the 11th axis and i

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

761-770 of Total 1368

prev 77 / 137page next

New function of EXCELLENT

The new function includes:- PI control function- Cumulative energy monitor (monitor accuracy: approximately ±25% of full scale value)- Response current limit... More Details >>
- No：21660
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A100
Encoder cable length restriction

If the cable length is longer than 100 m, speed may not be read correctly due to voltage drop and waveform deformation of the encoder signal. Therefore, use ... More Details >>
- No：21932
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-V200
Rated capacity related to harmonic suppression guidelines

The usual inverter input current is determined not by the inverter capacity but by the motor capacity (motor load).Therefore, the input side capacity is not ... More Details >>
- No：21961
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Others
Motor retention at 0 Hz

The inverter does not have a function to limit the current at 0 Hz.Although it has the DC injection brake, it is intended to improve the braking capability b... More Details >>
- No：22002
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Two-rank up maximum short-time torque

It is not possible to generate torque larger than the maximum possible torque of the motor by increasing the inverter's capacity.Even when the inverter is up... More Details >>
- No：22027
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Impossible to recover after power failure

First, ensure that the parameter for automatic restart after instantaneous power failure is set correctly and then do the following:1. Check if the terminals... More Details >>
- No：22033
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Using shielded wires for frequency meter connection

Connect the shield to the terminal SD. More Details >>
- No：22034
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Reset command during operation

The reset signal does not damage the inverter.It seems that the inverter went faulty due to other reasons.Mitsubishi Electric FA Center can inspect the inver... More Details >>
- No：22065
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Digital input and maximum frequency

1. Pr.1 and 18 limit the output to 120 Hz. Use Pr.18 to change the maximum frequency. 2. If you want to output the binary input as is, setting Pr.304 = 1 (Bi... More Details >>
- No：22098
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Plug-in Options , FREQROL-A500
Relationship between rotary switch and axis number

When the rotary switch is “0”, the 1st axis and is “1”, the 2nd axis. When the rotary switch is “A”, the 11th axis and is “F”, the 16th axis. In combination ... More Details >>
- No：23644
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4

761-770 of Total 1368

Inquiries

page top