Please refer to the section "Terminal box installation location and direction of lead wire outlet" of the general catalo

Since the Advanced magnetic flux vector control method uses slip compensation to compensate the frequency, the value is

Since Advanced magnetic flux vector control is chosen, the inverter calculates how much the motor rotation slips from th

Vector control performs high-accuracy calculation using the motor constant. Therefore, to perform vector control operati

You can switch between PU operation and external operation using the plug-in option "12-bit digital input" card and exte

The potentiometer on the operation panel is initially calibrated so that the maximum indication is slightly over 60 Hz w

1. When the inverter power supply is turned OFF, the inverter is disconnected from the CC-Link network. However, since t

The wiring length of the start signal (STF etc.) is 30 m or less. The circuit voltage of the control input signals (term

It is one of other communication errors. The communication is not established. Check the communication settings.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

761-770 of Total 1368

prev 77 / 137page next

About changing the direction of the cable entrance for the terminal box

Please refer to the section "Terminal box installation location and direction of lead wire outlet" of the general catalogue. However, GM-J2 series is not su... More Details >>
- No：20763
- Release Date：2018/08/21 16:10
- Update：2018/09/04 15:06
- Category： Geared Motors Parallel shaft type , Geared Motors Right angle shaft type , S-PM Geared Motors Parallel shaft type , S-PM Geared Motors Right angle shaft type
Frequency setting

Since the Advanced magnetic flux vector control method uses slip compensation to compensate the frequency, the value is not shown as exactly 60 Hz.For V/F co... More Details >>
- No：21807
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Frequency setting

Since Advanced magnetic flux vector control is chosen, the inverter calculates how much the motor rotation slips from the flowing current and adds the slip a... More Details >>
- No：21684
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Auto tuning

Vector control performs high-accuracy calculation using the motor constant. Therefore, to perform vector control operation, the inverter must recognize the m... More Details >>
- No：21663
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-V200
12-bit digital input and others

You can switch between PU operation and external operation using the plug-in option "12-bit digital input" card and external contact signals. After setting P... More Details >>
- No：21432
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-A200
Indication of potentiometer on operation panel

The potentiometer on the operation panel is initially calibrated so that the maximum indication is slightly over 60 Hz with the potentiometer turned to the m... More Details >>
- No：21427
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Countermeasures when input power supply is turned off upon equipment fault

1. When the inverter power supply is turned OFF, the inverter is disconnected from the CC-Link network. However, since the CC-Link master station has the aut... More Details >>
- No：21390
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Remote operation of the inverter

The wiring length of the start signal (STF etc.) is 30 m or less. The circuit voltage of the control input signals (terminal STF etc.) is 24 VDC and the volt... More Details >>
- No：21380
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Remote register when instruction code execution request is issued at CC-Link communication

The value "0" is stored. More Details >>
- No：21234
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
FR-SW1-SETUP

It is one of other communication errors. The communication is not established. Check the communication settings. More Details >>
- No：21176
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Engineering Software

761-770 of Total 1368

Inquiries

page top