It indicate that the actual number of connectable units differs depending on the master side specification although the

It is recommended to install the magnetic contactor on the input side of the inverter for safety. The category 3 can be

For the normal type (FR-B3) is 2 KHz. For the low-noise type (FR-B3-N), 14.5 KHz.

It is necessary to select the size of the reduction gear section that has mechanical strength equivalent to the output c

SHY right angle shaft type has lineup of flange and face mounting. For face mount type, screw hole processing is done on

Use the option cable, “MR-J3CN6CBL1M” for the analog monitor of MR-J4-A.

Using MR Configurator2, you can switch the output signals on/off forcibly independently of the servo status. This functi

The module power consumption displays the power consumption of servo motor. Positive value indicates power running and n

The phase detection terminal has been provided with units produced since December 1999. You can identify these units wit

1. By changing RWw1 while RYD is ON, you can change the inverter's frequency.You cannot do this with RYE. You need to tu

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

781-790 of Total 1353

prev 79 / 136page next

FR-A800-E

It indicate that the actual number of connectable units differs depending on the master side specification although the maximum number of connectable units o... More Details >>
- No：20839
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-A800
Safety stop function of the FR-D700/FR-E700

It is recommended to install the magnetic contactor on the input side of the inverter for safety. The category 3 can be satisfied without installing it. More Details >>
- No：20837
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700
Setting value of Pr.72 (FR-B, B3 (A800 base))

For the normal type (FR-B3) is 2 KHz. For the low-noise type (FR-B3-N), 14.5 KHz. More Details >>
- No：20828
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-B
Regarding service factors

It is necessary to select the size of the reduction gear section that has mechanical strength equivalent to the output converted to steady load condition tak... More Details >>
- No：20779
- Release Date：2018/08/21 16:10
- Category： Geared Motors Parallel shaft type , Geared Motors Right angle shaft type , S-PM Geared Motors Parallel shaft type , S-PM Geared Motors Right angle shaft type
Differences between flange and face mounting

SHY right angle shaft type has lineup of flange and face mounting. For face mount type, screw hole processing is done on the flange surface of the gear case,... More Details >>
- No：20778
- Release Date：2018/08/21 16:10
- Category： Geared Motors Right angle shaft type , S-PM Geared Motors Right angle shaft type
Monitor cable

Use the option cable, “MR-J3CN6CBL1M” for the analog monitor of MR-J4-A. More Details >>
- No：23655
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4
Output check

Using MR Configurator2, you can switch the output signals on/off forcibly independently of the servo status. This function is used for output signal wiring c... More Details >>
- No：23639
- Release Date：2018/09/14 15:10
- Category： Servo Support Software , MELSERVO-J4 , MELSERVO-JE , MELSERVO-JN , MELSERVO-J3
Unit power consumption

The module power consumption displays the power consumption of servo motor. Positive value indicates power running and negative value indicates regeneration. More Details >>
- No：23636
- Release Date：2018/09/14 15:10
- Category： Servo Support Software , MELSERVO-J4 , MELSERVO-JE
Phase detection terminal

The phase detection terminal has been provided with units produced since December 1999. You can identify these units with the serial number "N9Z○○○○○○" or la... More Details >>
- No：22090
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
Operation with CC-Link

1. By changing RWw1 while RYD is ON, you can change the inverter's frequency.You cannot do this with RYE. You need to turn OFF and then ON RYE each time you ... More Details >>
- No：22083
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500

781-790 of Total 1353

Inquiries

page top