Use the RUN signal to turn ON and OFF the brake.Using the MRS (output shutoff) signal to turn ON the brake shuts off the

Since the inverter's fault contact is an NC contact, it does not open unless a fault occurs.Therefore, when the control

Vector control cannot be selected unless Pr.862 is set to 1. Only the first motor is supported in the motor setting of F

The torque limit setting is defined as an absolute value. Thus, when -100% is written to the torque limit, the torque is

Yes, it is preferred. The accuracy becomes worse when the gap between the setting value and actual value increases.

The same value is displayed in the initial setting. When negative output is enabled by setting "0" to Pr.290 (Monitor ne

Because the internal reset processing is performed when the power supply is turned OFF, the fault state cannot be held.

The FR-CC2 has a built-in EMC filter (radio noise filter).

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

71-80 of Total 1354

prev 8 / 136page next

When controlling motor with brake by inverter

Use the RUN signal to turn ON and OFF the brake.Using the MRS (output shutoff) signal to turn ON the brake shuts off the inverter's output and reduces influe... More Details >>
- No：21960
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Fault contact when connecting separate power supply for each control circuit

Since the inverter's fault contact is an NC contact, it does not open unless a fault occurs.Therefore, when the control power supply (and main circuit power ... More Details >>
- No：22035
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Safety stop function of the FR-E700/FR-D700

Up to two. More Details >>
- No：20827
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL
FR Configurator2

Vector control cannot be selected unless Pr.862 is set to 1. Only the first motor is supported in the motor setting of FR Configurator2. More Details >>
- No：20847
- Release Date：2018/08/22 16:24
- Category： Engineering Software
FR-A8NC

The torque limit setting is defined as an absolute value. Thus, when -100% is written to the torque limit, the torque is limited at 100%. More Details >>
- No：20920
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
FR-A800-CRN

Yes, it is preferred. The accuracy becomes worse when the gap between the setting value and actual value increases. More Details >>
- No：20932
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
FR-A800-CRN

Yes, it is included. More Details >>
- No：20933
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
Difference in the monitor function

The same value is displayed in the initial setting. When negative output is enabled by setting "0" to Pr.290 (Monitor negative output selection), there are f... More Details >>
- No：20938
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
FR-PU07BB

Because the internal reset processing is performed when the power supply is turned OFF, the fault state cannot be held. The details of the faults are saved i... More Details >>
- No：20942
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options
FR-CC2

The FR-CC2 has a built-in EMC filter (radio noise filter). More Details >>
- No：20951
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL

71-80 of Total 1354

Inquiries

page top