They cannot be set with the frequency. Because the command is input at the line speed, consider the line speed of the in

Connect the line noise filter between the inverter and EMC Directive compliant noise filter.

It is recommended to turn OFF the start signals (STF and STR) when stopping the inverter.In this case, it is not probabl

Under Advanced magnetic flux vector control, the output frequency varies due to slip compensation. This may cause the ou

The output torque characteristics of the FREQROL-E500 series are shown in the figure below. Figure 1

Set the parameters below. For other parameters, keep the initial settings.1. Set Pr.122 (Communication check time interv

Check the parameters necessary for tuning again.Check if Pr.9 (Electronic thermal O/L relay) and Pr.81 (Number of motor

Only the operation command source is switched to the FR-A07 and the inverter operation panel does not turn off. (Setting

Auto tuning targets an induction motor. 1. You can perform auto tuning on a wound rotor motor. After performing auto tun

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

791-800 of Total 1353

prev 80 / 136page next

FR-A800-R2R

They cannot be set with the frequency. Because the command is input at the line speed, consider the line speed of the initial winding diameter at 20 Hz. The ... More Details >>
- No：20888
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-A800
Connection point of the line noise filter

Connect the line noise filter between the inverter and EMC Directive compliant noise filter. More Details >>
- No：20818
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Options
Operation at external operation/stop

It is recommended to turn OFF the start signals (STF and STR) when stopping the inverter.In this case, it is not probable that the motor rotates due to a cal... More Details >>
- No：22102
- Release Date：2018/08/22 16:31
- Category： Inverters-FREQROL , FREQROL-E500
Pulse train output of terminal FM

Under Advanced magnetic flux vector control, the output frequency varies due to slip compensation. This may cause the output frequency monitor value to chang... More Details >>
- No：22054
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Relationship between frequency and output torque

The output torque characteristics of the FREQROL-E500 series are shown in the figure below. Figure 1 More Details >>
- No：22024
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500
Inverter setup

Set the parameters below. For other parameters, keep the initial settings.1.　Set Pr.122 (Communication check time interval) to other than "0". ("9999" is OK.... More Details >>
- No：21986
- Release Date：2018/08/22 16:30
- Category： Engineering Software
Advanced magnetic flux vector control

Check the parameters necessary for tuning again.Check if Pr.9 (Electronic thermal O/L relay) and Pr.81 (Number of motor poles) are set correctly. More Details >>
- No：21754
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Auto tuning

Yes. More Details >>
- No：21749
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
FR-PA07

Only the operation command source is switched to the FR-A07 and the inverter operation panel does not turn off. (Setting from the inverter operation panel be... More Details >>
- No：21699
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ
Auto tuning enabled motor

Auto tuning targets an induction motor. 1. You can perform auto tuning on a wound rotor motor. After performing auto tuning, check operation in test run. 2. ... More Details >>
- No：21636
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A200

791-800 of Total 1353

Inquiries

page top