The basic idea is the same, but the total capacity should be 3.7 kW. (The maximum capacity is also 3.7K.)

It is considered that conditions including the power supply and noise change whether the parameter unit is connected or

There is a 10 ms delay after the inverter recognizes the start command (STF OR STR) before it starts decelerating. The d

When the heat sink is outside, since the heat sink and fan are not waterproof, you need to enclose them so that they are

You can connect multiple inverters to a single reactor. In this case, the load seems to be light from the reactor unless

Available under vector control with an encoder.* Zero speed and servo lock are available under PM sensorless vector cont

If the command is 0.01 Hz or higher, the positioning control is performed.

Do not carry out a pressure test. As for a megger test, carry out the test with 500 VDC as describes in the Instruction

For the safety of use, the wiring is recommended. If not using the wiring, set the parameter No. PA04 to “0100”.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

801-810 of Total 1353

prev 81 / 136page next

Number of inverters that can be connected to a 20 A branch circuit breaker

The basic idea is the same, but the total capacity should be 3.7 kW. (The maximum capacity is also 3.7K.) More Details >>
- No：21508
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Others , FREQROL-A024
Rotations per minute vary

It is considered that conditions including the power supply and noise change whether the parameter unit is connected or disconnected, influencing the analog ... More Details >>
- No：21454
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-V200
Inverter signal input speed

There is a 10 ms delay after the inverter recognizes the start command (STF OR STR) before it starts decelerating. The delay is 10 ms. A delay of 100 ms is i... More Details >>
- No：21445
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
FR-A5CN

When the heat sink is outside, since the heat sink and fan are not waterproof, you need to enclose them so that they are not exposed to the spray of water. More Details >>
- No：21435
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Options
Installing reactor for suppressing harmonics

You can connect multiple inverters to a single reactor. In this case, the load seems to be light from the reactor unless all of the inverters are rotating an... More Details >>
- No：21410
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Options
Auto tuning

Set "33" or "34". More Details >>
- No：21167
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700
FR-A800

Available under vector control with an encoder.* Zero speed and servo lock are available under PM sensorless vector control only in combination with an MM-CF... More Details >>
- No：21100
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800
MM-FR-A800

If the command is 0.01 Hz or higher, the positioning control is performed. More Details >>
- No：21001
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800
FR-HC2

Do not carry out a pressure test. As for a megger test, carry out the test with 500 VDC as describes in the Instruction Manual of the inverter. More Details >>
- No：20967
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Others , Peripheral devices
Is the forced stop signal wiring necessary?

For the safety of use, the wiring is recommended. If not using the wiring, set the parameter No. PA04 to “0100”. More Details >>
- No：23645
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4

801-810 of Total 1353

Inquiries

page top