1. Maximum torque available for output from the motor when combined with an inverter for a short period of time (1 minut

You can calculate the torque from the power. From the general equation: Pout = ωn × TT = (Pout × τ)/ωnPout: Measured va

Similarly to the FR-A200 and A500, four or more filters should be used also for the FR-A100. In short, it is OK if the

There is a 10 ms delay after the inverter recognizes the start command (STF OR STR) before it starts decelerating. The d

The inverter alarm "OV3" occurs when the main circuit DC voltage inside the inverter goes higher than the preset value d

When the heat sink is outside, since the heat sink and fan are not waterproof, you need to enclose them so that they are

You can input current from the terminal AM of the inverter to the programmable controller (for A/D conversion) and contr

When the high power factor converter is installed, you can use the conversion coefficient of K5 = 0 for calculation. In

Answer to question 1 When the CC-Link option goes faulty, OPT (option error) occurs and the inverter's fault output is t

The speed fluctuation ratio under Advanced magnetic flux vector control of the FR-A500 is as follows. Without encoder: ±

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

831-840 of Total 1368

prev 84 / 137page next

Term definition and advanced magnetic flux control

1. Maximum torque available for output from the motor when combined with an inverter for a short period of time (1 minute or less). 　　It depends on the contr... More Details >>
- No：21541
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
How can I calculate the processing torque from the measured power?

You can calculate the torque from the power. 　From the general equation: Pout = ωn × TT = (Pout × τ)/ωnPout: Measured valueωn: Actual motor shaft angular fre... More Details >>
- No：21475
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Others , FREQROL-A500
Difference between use with A100 and other types

Similarly to the FR-A200 and A500, four or more filters should be used also for the FR-A100. 　In short, it is OK if the wire penetrates the filter four times... More Details >>
- No：21468
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Options
Inverter signal input speed

There is a 10 ms delay after the inverter recognizes the start command (STF OR STR) before it starts decelerating. The delay is 10 ms. A delay of 100 ms is i... More Details >>
- No：21445
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Countermeasure against error

The inverter alarm "OV3" occurs when the main circuit DC voltage inside the inverter goes higher than the preset value due to the regenerative power returned... More Details >>
- No：21438
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A024
FR-A5CN

When the heat sink is outside, since the heat sink and fan are not waterproof, you need to enclose them so that they are not exposed to the spray of water. More Details >>
- No：21435
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Options
Load current limit of inverter

You can input current from the terminal AM of the inverter to the programmable controller (for A/D conversion) and control the speed with the software of the... More Details >>
- No：21419
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Countermeasure against harmonics

When the high power factor converter is installed, you can use the conversion coefficient of K5 = 0 for calculation. In accordance with the harmonic suppress... More Details >>
- No：21398
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Others
Using FR-A540 inverter on CC-Link

Answer to question 1 When the CC-Link option goes faulty, OPT (option error) occurs and the inverter's fault output is triggered. When communication is lost ... More Details >>
- No：21391
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Vector control of the inverter

The speed fluctuation ratio under Advanced magnetic flux vector control of the FR-A500 is as follows. Without encoder: ±1% With encoder (with A5AP): ±0. 02 %... More Details >>
- No：21369
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500

831-840 of Total 1368

Inquiries

page top