1. When the inverter power supply is turned OFF, the inverter is disconnected from the CC-Link network. However, since t

1. Since you can monitor the output frequency independently, you do not need to switch monitoring by the monitor command

The high speed command (multi-speed command) is prioritized over the frequency setting potentiometer. It is OK if these

You can switch between PU operation and external operation using the plug-in option "12-bit digital input" card and exte

Possible causes are:1. The reset signal (RES) is ON. 2. The built-in CPU is not working properly due to contact faults o

The following are check points for abnormal conditions in addition to those given in the FR-Z200 manual. 1. Are the for

The basic idea is the same, but the total capacity should be 3.7 kW. (The maximum capacity is also 3.7K.)

Connection method for the A500 and E500 is shown in the figure below. The figure is given in an Excel file. Figure 1

You can remove the parameter unit FR-PU02 and install the FR-CU01 there. However, since the interface for the parameter

Use the plug-in option dedicated for the FR-A200EXECLLENT. The plug-in option for the FR-A200EXECLLENT cannot be used wi

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

861-870 of Total 1368

prev 87 / 137page next

Countermeasures when input power supply is turned off upon equipment fault

1. When the inverter power supply is turned OFF, the inverter is disconnected from the CC-Link network. However, since the CC-Link master station has the aut... More Details >>
- No：21390
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
CC-Link monitor and parameter setting

1. Since you can monitor the output frequency independently, you do not need to switch monitoring by the monitor commands. Assign the remote register RWr0 to... More Details >>
- No：21418
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Speed setting

The high speed command (multi-speed command) is prioritized over the frequency setting potentiometer. It is OK if these are both input simultaneously. When t... More Details >>
- No：21424
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-U100
12-bit digital input and others

You can switch between PU operation and external operation using the plug-in option "12-bit digital input" card and external contact signals. After setting P... More Details >>
- No：21432
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-A200
"Err" is displayed when STF signal turns ON

Possible causes are:1. The reset signal (RES) is ON. 2. The built-in CPU is not working properly due to contact faults of the inverter parts. Check the exte... More Details >>
- No：21484
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Is this a failure?

The following are check points for abnormal conditions in addition to those given in the FR-Z200 manual. 　1. Are the forward and reverse signals input simult... More Details >>
- No：21503
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-Z200
Number of inverters that can be connected to a 20 A branch circuit breaker

The basic idea is the same, but the total capacity should be 3.7 kW. (The maximum capacity is also 3.7K.) More Details >>
- No：21508
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Others , FREQROL-A024
Connection with personal computer

Connection method for the A500 and E500 is shown in the figure below. The figure is given in an Excel file. Figure 1 More Details >>
- No：21536
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Communication option

You can remove the parameter unit FR-PU02 and install the FR-CU01 there. However, since the interface for the parameter unit is used, the communication speed... More Details >>
- No：21625
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Others , FREQROL-A200
Plug-in options

Use the plug-in option dedicated for the FR-A200EXECLLENT. The plug-in option for the FR-A200EXECLLENT cannot be used with the FR-A200. To avoid installing a... More Details >>
- No：21634
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Plug-in Options , FREQROL-A200

861-870 of Total 1368

Inquiries

page top