1. Maximum torque available for output from the motor when combined with an inverter for a short period of time (1 minut

To control multiple inverters using arbitrary signals (4 to 20 mA) simultaneously, it is recommended to connect the sign

1. Torque control automatically adjust the speed so that the instructed torque value is maintained. This means that the

Set "13" in Pr.71. Always perform auto tuning.

Yes, it does. (There are some restrictions.

Since the lower limit has been internally set, 3% or less is recognized as 3%.

The count is resumed from 0. Thus, the times of the overflow is reset.

Vector control cannot be selected unless Pr.862 is set to 1. Only the first motor is supported in the motor setting of F

Air pressure falls by about 100 hPa for every 1,000 meters higher you go. This results in the air becomes thinner and a

The RX7 output signal is the same as the signals for NO, NC, and transfer contact output.You can change the contents of

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

861-870 of Total 1368

prev 87 / 137page next

Term definition and advanced magnetic flux control

1. Maximum torque available for output from the motor when combined with an inverter for a short period of time (1 minute or less). 　　It depends on the contr... More Details >>
- No：21541
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Controlling multiple VVVFs via communication from personal computer

To control multiple inverters using arbitrary signals (4 to 20 mA) simultaneously, it is recommended to connect the signals (4 to 20 mA) in series. (This doe... More Details >>
- No：21491
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Unwinding using vector inverter

1. Torque control automatically adjust the speed so that the instructed torque value is maintained. This means that the speed is not controlled. (However, yo... More Details >>
- No：21420
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-V200
Advanced magnetic flux vector control

Set "13" in Pr.71. Always perform auto tuning. More Details >>
- No：21299
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700
FR-A8TAT

Yes, it does. (There are some restrictions. More Details >>
- No：21082
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options , FREQROL-A800
Gain adjustment under the speed control

Since the lower limit has been internally set, 3% or less is recognized as 3%. More Details >>
- No：21016
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , FREQROL-F800
Cumulative pulse monitor

The count is resumed from 0. Thus, the times of the overflow is reset. More Details >>
- No：20902
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
FR Configurator2

Vector control cannot be selected unless Pr.862 is set to 1. Only the first motor is supported in the motor setting of FR Configurator2. More Details >>
- No：20847
- Release Date：2018/08/22 16:24
- Category： Engineering Software
Regarding altitude restrictions

Air pressure falls by about 100 hPa for every 1,000 meters higher you go. This results in the air becomes thinner and a drop in cooling capacity. This can re... More Details >>
- No：20781
- Release Date：2018/08/21 16:10
- Category： Geared Motors Parallel shaft type , Geared Motors Right angle shaft type , S-PM Geared Motors Parallel shaft type , S-PM Geared Motors Right angle shaft type
Alarm output signal when using CC-Link

The RX7 output signal is the same as the signals for NO, NC, and transfer contact output.You can change the contents of this output signal using Pr.192.Pr.19... More Details >>
- No：22008
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500

861-870 of Total 1368

Inquiries

page top