The inverter restart operation is disabled at turn-OFF of the CS signal while a value other than "9999" (with restart) i

After setting Pr.79 (Operation mode selection) to "2" and Pr.340 (Communication startup mode selection) to "10", reset t

It is considered that communication settings between the inverter and personal computer do not match. Check if settings

Since the inverter displayed "0.00" instead of an error when the inverter speed dropped to 0 Hz and stopped by holding t

If all inverters are in regenerative operation, the regenerative power is regenerated to the power supply. If one of the

FR-E700, D700, and F700PJ do not have the terminal CS and you can only control automatic restart by setting Pr.57 (Resta

If you have already set other parameters necessary for tuning (Pr.9, Pr.71, Pr.80, Pr.81, Pr.83, and Pr.84), press the M

This subroutine is to check the data link status and needs to be executed only once at the start of the program.

The start commands cannot be input from both sources simultaneously because the operation command source is specified.Yo

It is OK if stations are set as reserved.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

881-890 of Total 1368

prev 89 / 137page next

Automatic restart after instantaneous power failure

The inverter restart operation is disabled at turn-OFF of the CS signal while a value other than "9999" (with restart) is set in Pr.57. The terminals CS and ... More Details >>
- No：21255
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
CC-Link communication

After setting Pr.79 (Operation mode selection) to "2" and Pr.340 (Communication startup mode selection) to "10", reset the inverter (or power ON again) to st... More Details >>
- No：21256
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Inverter data cannot be read

It is considered that communication settings between the inverter and personal computer do not match. Check if settings such as communication rate and stop b... More Details >>
- No：21431
- Release Date：2018/08/22 16:27
- Category： Engineering Software
Speed does not exceed 46 Hz

Since the inverter displayed "0.00" instead of an error when the inverter speed dropped to 0 Hz and stopped by holding the winding machine by hand, it is con... More Details >>
- No：21492
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Regenerative power flow

If all inverters are in regenerative operation, the regenerative power is regenerated to the power supply. If one of the inverters is power driving, the rege... More Details >>
- No：21564
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Terminal CS

FR-E700, D700, and F700PJ do not have the terminal CS and you can only control automatic restart by setting Pr.57 (Restart coasting time). More Details >>
- No：21707
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ
Auto tuning

If you have already set other parameters necessary for tuning (Pr.9, Pr.71, Pr.80, Pr.81, Pr.83, and Pr.84), press the MODE button to return to the frequency... More Details >>
- No：21750
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Program command

This subroutine is to check the data link status and needs to be executed only once at the start of the program. More Details >>
- No：21767
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
CC-Link

The start commands cannot be input from both sources simultaneously because the operation command source is specified.You can switch the command source as ne... More Details >>
- No：21828
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
CC-Link

It is OK if stations are set as reserved. More Details >>
- No：21868
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P

881-890 of Total 1368

Inquiries

page top