An earth plate permanently installed in the 700 series is included as an option for the 800 series because of the change

Yes. However, it is difficult to wind the twisted wires because they are thick.

Three phases are measured with the CT. The accuracy is ±10 % which is same as the inverter output current.

The acceleration time is 60 Hz and 5 seconds, and deceleration time is 60 Hz and 60 seconds.

No. During JOG operation, deceleration stop is performed even though Pr.250 is set.

When the second torque limit is used, the settings of Pr.816 and 817 are valid.

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring.

Other than "0" can be input. The inverter is reset by writing any numerical value.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

81-90 of Total 1368

prev 9 / 137page next

Included earth plate

An earth plate permanently installed in the 700 series is included as an option for the 800 series because of the change of the shape of the circuit board. More Details >>
- No：21035
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
PLC function

It depends on the scan time. More Details >>
- No：21042
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
Line noise filter

Yes. However, it is difficult to wind the twisted wires because they are thick. More Details >>
- No：21128
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Options
FR-HC2

Three phases are measured with the CT. The accuracy is ±10 % which is same as the inverter output current. More Details >>
- No：21145
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Options
FR-FS

The acceleration time is 60 Hz and 5 seconds, and deceleration time is 60 Hz and 60 seconds. More Details >>
- No：21166
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Stop selection

No. During JOG operation, deceleration stop is performed even though Pr.250 is set. More Details >>
- No：21199
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Carrier frequency

It is fixed to 5 kHz. More Details >>
- No：21211
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Torque limit

When the second torque limit is used, the settings of Pr.816 and 817 are valid. More Details >>
- No：21218
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
LED blinking under encoder feedback control

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring. More Details >>
- No：21220
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
System environment variable of the Modbus-RTU communication

Other than "0" can be input. The inverter is reset by writing any numerical value. More Details >>
- No：21224
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

81-90 of Total 1368

Inquiries

page top