The speed fluctuation ratio under Advanced magnetic flux vector control of the FR-A500 is as follows. Without encoder: ±

For tuning of a single motor with no load, set Pr.96 to "101". When a load is connected, set Pr.96 to "1" (without motor

It can be used with the FR-A700 and FR-E700 series.

Pr.59 is available in the products manufactured in October 1995 or later. Therefore, it cannot be read from the products

It is not completely recommended to use F700P because the starting torque at low speed of the hydraulic pump may be larg

The leakage current is 1 mA because the circuit constant in the EMC filter of A720-0.4K and 0.75K are different.

No. Check the parameter setting of the A700, and then adjust the parameter setting of the A800 to those of the A700. For

The number of terminals: There are the same output terminals as F700P and the following terminals (2 points) are added.

The specifications are the same. The same cable gauge is available.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

891-900 of Total 1353

prev 90 / 136page next

Vector control of the inverter

The speed fluctuation ratio under Advanced magnetic flux vector control of the FR-A500 is as follows. Without encoder: ±1% With encoder (with A5AP): ±0. 02 %... More Details >>
- No：21369
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Real sensorless vector control

For tuning of a single motor with no load, set Pr.96 to "101". When a load is connected, set Pr.96 to "1" (without motor rotation). Since Real sensorless vec... More Details >>
- No：21325
- Release Date：2018/08/22 16:27
- Category： FREQROL-A700
Advanced magnetic flux vector control

It can be used with the FR-A700 and FR-E700 series. More Details >>
- No：21298
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Carrier frequency

It is fixed to 5 kHz. More Details >>
- No：21211
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
FR-A024

Pr.59 is available in the products manufactured in October 1995 or later. Therefore, it cannot be read from the products manufactured before October 1995. More Details >>
- No：21170
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A024
Selection

It is not completely recommended to use F700P because the starting torque at low speed of the hydraulic pump may be larger than that of the normal pump. Sele... More Details >>
- No：21126
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Others
FR-A700

The leakage current is 1 mA because the circuit constant in the EMC filter of A720-0.4K and 0.75K are different. More Details >>
- No：21120
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700
FR-A800

No. Check the parameter setting of the A700, and then adjust the parameter setting of the A800 to those of the A700. For the details, refer to the replacemen... More Details >>
- No：21107
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , FREQROL-A700
The number of output terminals

The number of terminals: There are the same output terminals as F700P and the following terminals (2 points) are added. Safety: SO, SOC *The terminals SO and... More Details >>
- No：21069
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-F800
Terminal block

The specifications are the same. The same cable gauge is available. More Details >>
- No：21052
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL

891-900 of Total 1353

Inquiries

page top