It is not recommended to install a contactor on the input side and connect the auxiliary contact to the terminal STF of

"8" display in offline auto tuning means forced stop by the operator. This means that you stopped operation before tunin

The inverter efficiency (power factor) for the inverter alone is approximately 75 to 80%. However, by installing the pow

Energy saving is achieved by switching from the commercial power supply to the inverter to operate the motor. When the

1. You can connect them using △ connection. 2. No problem with connecting four Y-△ motors. (Connect all four motors usin

Perform calculation given in the harmonic suppression guidelines, and if the limit value is exceeded, you may also need

There is a 10 ms delay after the inverter recognizes the start command (STF OR STR) before it starts decelerating. The d

The FM output is the 1440 Hz, 1 mA pulse train output at full scale. You can input to the programmable controller if it

The reactor built in the FREQROL-A201 series is intended to stabilize operation of the converter circuit and differs fro

We recommend the "YM206RI 1 mA" analog ammeter.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

901-910 of Total 1354

prev 91 / 136page next

Installing contactor on input side

It is not recommended to install a contactor on the input side and connect the auxiliary contact to the terminal STF of the inverter for the following reason... More Details >>
- No：21533
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL
Overcurrent at low speed

"8" display in offline auto tuning means forced stop by the operator. This means that you stopped operation before tuning completes. 　With this forced stop, ... More Details >>
- No：21527
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
A100 inverter loss

The inverter efficiency (power factor) for the inverter alone is approximately 75 to 80%. However, by installing the power factor improving DC reactor to the... More Details >>
- No：21512
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A100
Energy saving and power supply capacity of inverter

Energy saving is achieved by switching from the commercial power supply to the inverter to operate the motor. When the inverter reduces motor speed, it also... More Details >>
- No：21498
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Others
Compatibility with Y-△ motor and others

1. You can connect them using △ connection. 2. No problem with connecting four Y-△ motors. (Connect all four motors using △ connection.) (Note that the inver... More Details >>
- No：21487
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Others
Countermeasure against harmonics

Perform calculation given in the harmonic suppression guidelines, and if the limit value is exceeded, you may also need to insert the ACL. Note that you cann... More Details >>
- No：21465
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Options
Inverter signal input speed

There is a 10 ms delay after the inverter recognizes the start command (STF OR STR) before it starts decelerating. The delay is 10 ms. A delay of 100 ms is i... More Details >>
- No：21445
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Monitor output

The FM output is the 1440 Hz, 1 mA pulse train output at full scale. You can input to the programmable controller if it has a pulse train input. A68AD does n... More Details >>
- No：21439
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A024
Built-in reactor

The reactor built in the FREQROL-A201 series is intended to stabilize operation of the converter circuit and differs from the FR-BAL. Note that when performi... More Details >>
- No：21421
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Options , Others
Analog ammeter

We recommend the "YM206RI 1 mA" analog ammeter. More Details >>
- No：21402
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Options

901-910 of Total 1354

Inquiries

page top