The carrier frequency is initially set to 7 kHz. (When Pr.10 is set to "---", you can set or change the setting using Pr

When offline auto tuning ends normally, the setting of this parameter changes to "3".This means that auto tuning complet

1. You can set Pr.117 for "n1" (Station number) of the FR-S500 for the D700/E700/F700PJ series.2. You can set Pr.338, Pr

The start commands cannot be input from both sources simultaneously because the operation command source is specified.Yo

Set the parameters below. For other parameters, keep the initial settings.1. Set Pr.122 (Communication check time interv

1. Changing frequency to 0 Hz(1) Set Pr.8 (Deceleration time) to 0 second.If the load is large, the stall prevention fun

The resistor unit MT-BR5 manufactured in February 2016 or later has output terminal TH3 (NC contact) as a fault output t

The English version cannot be updated from the Website. FR-SW3-SETUP-WE needs to be purchased.

It decelerates and stops. The operation is the same as the one when the Bit of forward rotation command and reverse rota

Since the operation panel and PU connector cannot be specified for command source at the same time, they cannot be used

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

911-920 of Total 1368

prev 92 / 137page next

Carrier frequency of low-noise series

The carrier frequency is initially set to 7 kHz. (When Pr.10 is set to "---", you can set or change the setting using Pr.72.) Raising the carrier frequency r... More Details >>
- No：21600
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-U100
Auto tuning

When offline auto tuning ends normally, the setting of this parameter changes to "3".This means that auto tuning completed normally.If the setting value is "... More Details >>
- No：21748
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
RS-485 communication

1. You can set Pr.117 for "n1" (Station number) of the FR-S500 for the D700/E700/F700PJ series.2. You can set Pr.338, Pr.339, and Pr.342 for "n8" (Operation ... More Details >>
- No：21758
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ
CC-Link

The start commands cannot be input from both sources simultaneously because the operation command source is specified.You can switch the command source as ne... More Details >>
- No：21828
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Inverter setup

Set the parameters below. For other parameters, keep the initial settings.1.　Set Pr.122 (Communication check time interval) to other than "0". ("9999" is OK.... More Details >>
- No：21986
- Release Date：2018/08/22 16:30
- Category： Engineering Software
Usage

1. Changing frequency to 0 Hz(1) Set Pr.8 (Deceleration time) to 0 second.If the load is large, the stall prevention function may work to lengthen decelerati... More Details >>
- No：22019
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500
TH3 terminal of the MT-BR5

The resistor unit MT-BR5 manufactured in February 2016 or later has output terminal TH3 (NC contact) as a fault output terminal. More Details >>
- No：20816
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Options
FR Configurator (English version)

The English version cannot be updated from the Website. FR-SW3-SETUP-WE needs to be purchased. More Details >>
- No：21195
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
System environment variable of the Modbus-RTU communication

It decelerates and stops. The operation is the same as the one when the Bit of forward rotation command and reverse rotation command are turned OFF. More Details >>
- No：21222
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Operation panel and FR-PA07

Since the operation panel and PU connector cannot be specified for command source at the same time, they cannot be used together. More Details >>
- No：21349
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ

911-920 of Total 1368

Inquiries

page top