An inverter is used to rotate a motor but it cannot be used to detect whether the belt is broken or not. However, the ma

The following are check points for abnormal conditions in addition to those given in the FR-Z200 manual. 1. Are the for

PWM is an acronym for Pulse Width Modulation and varies the switching pulse width of transistors. This method creates ma

Pre-excitation is the process to control current while a motor is stopped so that motor torque can be generated immediat

Remove the parameter unit FR-PU03 and install there. (The installation dimensions of the FR-CU03 are the same as the FR-

The terminal MRS assignment parameter is Pr.183. Set Pr.183 to "4" (AU). (This setting is for the E700.)

Many geared motors cannot continuously operate at low speed (for example, slower than 6 Hz) due to grease viscosity.If t

If the output current is close to 25% of the rated current, output phase loss may occur when one or two phases of three

From Start menu of Windows >, click [All Programs] > - [MELSOFT Application] > - [MR Configurator2] > and y

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

921-930 of Total 1368

prev 93 / 137page next

Detection of the motor load

An inverter is used to rotate a motor but it cannot be used to detect whether the belt is broken or not. However, the magnitude of the load will change when ... More Details >>
- No：21387
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Is this a failure?

The following are check points for abnormal conditions in addition to those given in the FR-Z200 manual. 　1. Are the forward and reverse signals input simult... More Details >>
- No：21503
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-Z200
PWM control

PWM is an acronym for Pulse Width Modulation and varies the switching pulse width of transistors.　This method creates many pulses within a single cycle of th... More Details >>
- No：21530
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Others
Pre-excitation, zero-speed control, and servo lock

Pre-excitation is the process to control current while a motor is stopped so that motor torque can be generated immediately. There are two methods for this p... More Details >>
- No：21562
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-V200
Installation of new serial communication unit FR-CU03

Remove the parameter unit FR-PU03 and install there. (The installation dimensions of the FR-CU03 are the same as the FR-PU.) You can read and write parameter... More Details >>
- No：21617
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A024
Terminal assignment

The terminal MRS assignment parameter is Pr.183. Set Pr.183 to "4" (AU). (This setting is for the E700.) More Details >>
- No：21850
- Release Date：2018/08/22 16:29
- Category： FREQROL-E700
Speed control range

Many geared motors cannot continuously operate at low speed (for example, slower than 6 Hz) due to grease viscosity.If the motor you are using is of this typ... More Details >>
- No：22028
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A024
Output phase loss alarm

If the output current is close to 25% of the rated current, output phase loss may occur when one or two phases of three phases go below 25%.Therefore, when a... More Details >>
- No：22052
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
MR-J4(W)-B mode selection application

From Start menu of Windows >, click [All Programs] > - [MELSOFT Application] > - [MR Configurator2] > and you can find “MR-J4(W)-B mode selectio... More Details >>
- No：23637
- Release Date：2018/09/14 15:10
- Category： Servo Support Software , MELSERVO-J4
FR-A8AZ

It is 12 bits (4096). More Details >>
- No：20969
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options

921-930 of Total 1368

Inquiries

page top