If Pr.361 = 0, the second terminal can be used as the line speed command when X114 is ON, and as the frequency setting v

When the value is written to Pr.646 (Stored winding diameter), the stored value is used. When the value is not written,

The FR-E7TR does not have the terminal for the SC and it cannot be used with the FR-E700-SC.

Yes, it does, however, it does not acquire the certification of the BACnet association standard.

Perform the writing after turning ON the SOF, or after stopping the FR-HC2 by pressing the STOP button. Wire the RDY sig

It is possible when Pr.23 = 0 (Current limit at regenerative driving).

The response delay time is 10 ms normally and 100 ms at startup.

The resistor unit MT-BR5 manufactured in February 2016 or later has output terminal TH3 (NC contact) as a fault output t

The following version or later is supported for Windows 8. MR Configurator2, 1.20W or later

It is considered that malfunction of the measurement device is due to noise. Check the noise propagation route since the

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

921-930 of Total 1368

prev 93 / 137page next

FR-A800-R2R

If Pr.361 = 0, the second terminal can be used as the line speed command when X114 is ON, and as the frequency setting value when X114 is OFF. If Pr.361 = 3,... More Details >>
- No：20891
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-A800
FR-A800-R2R

When the value is written to Pr.646 (Stored winding diameter), the stored value is used. When the value is not written, the minimum or maximum winding diamet... More Details >>
- No：20887
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-A800
FR-E700-SC

The FR-E7TR does not have the terminal for the SC and it cannot be used with the FR-E700-SC. More Details >>
- No：20865
- Release Date：2018/08/22 16:24
- Category： FREQROL-E700
FR-F800

Yes, it does, however, it does not acquire the certification of the BACnet association standard. More Details >>
- No：20863
- Release Date：2018/08/22 16:24
- Category： FREQROL-F800
FR-HC2

Perform the writing after turning ON the SOF, or after stopping the FR-HC2 by pressing the STOP button. Wire the RDY signal so that the inverter stops when t... More Details >>
- No：20842
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Options
FR-HC2

It is possible when Pr.23 = 0 (Current limit at regenerative driving). More Details >>
- No：20826
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Options
FR-A8AY

The response delay time is 10 ms normally and 100 ms at startup. More Details >>
- No：20821
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Plug-in Options
TH3 terminal of the MT-BR5

The resistor unit MT-BR5 manufactured in February 2016 or later has output terminal TH3 (NC contact) as a fault output terminal. More Details >>
- No：20816
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Options
Supported OS

The following version or later is supported for Windows 8. MR Configurator2, 1.20W or later More Details >>
- No：23633
- Release Date：2018/09/14 15:10
- Category： Servo Support Software
Influence on external measurement device

It is considered that malfunction of the measurement device is due to noise. Check the noise propagation route since the countermeasure depends on it. Some c... More Details >>
- No：22100
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Others

921-930 of Total 1368

Inquiries

page top