It cannot be connected. When using DU08, connect it to the PU connector.

If using an inverter with capacity of 75K or higher, or motor with capacity of 75 kW or higher, always select and instal

The carrier frequency for the FR-B3 is 2 kHz. For the low noise type FR-B3-N, it is 14.5 kHz.

After setting Pr.79 (Operation mode selection) to "2" and Pr.340 (Communication startup mode selection) to "10", reset t

Torque control cannot be performed with the FR-E700 series. It is available with the FR-A700 and FR-V500 series.

The parameter can be copied to only one inverter.

The USB connection requires FR Configurator (FR-SW3-SETUP-WJ) prepared by Mitsubishi Electric Corporation.

Press the "MODE" key on the operation panel several times to display "P.0" and parameter setting screen. Then turn the s

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

941-950 of Total 1353

prev 95 / 136page next

FR-DU08

It cannot be connected. When using DU08, connect it to the PU connector. More Details >>
- No：21111
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , FREQROL-F800
DC reactor

If using an inverter with capacity of 75K or higher, or motor with capacity of 75 kW or higher, always select and install the inverter based on the capacity ... More Details >>
- No：21112
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , Options , FREQROL-F800
FR-B3

The carrier frequency for the FR-B3 is 2 kHz. For the low noise type FR-B3-N, it is 14.5 kHz. More Details >>
- No：21181
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Options
Driving a single-phase motor

No, it cannot. More Details >>
- No：21253
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
CC-Link communication

After setting Pr.79 (Operation mode selection) to "2" and Pr.340 (Communication startup mode selection) to "10", reset the inverter (or power ON again) to st... More Details >>
- No：21256
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Torque control

Torque control cannot be performed with the FR-E700 series. It is available with the FR-A700 and FR-V500 series. More Details >>
- No：21279
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700
Speed command

Calibrate the terminal 2 bias. More Details >>
- No：21281
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Parameter copy of FR-Configurator

The parameter can be copied to only one inverter. More Details >>
- No：21306
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
USB connector

The USB connection requires FR Configurator (FR-SW3-SETUP-WJ) prepared by Mitsubishi Electric Corporation. More Details >>
- No：21318
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Parameter

Press the "MODE" key on the operation panel several times to display "P.0" and parameter setting screen. Then turn the setting dial to display "C..." screen ... More Details >>
- No：21336
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

941-950 of Total 1353

Inquiries

page top