From before, the QCPU has been used and each setting does not make a difference internally. Thus, the selection was redu

When the winding ratio is large, the control according to the winding diameter is required. The upper controller has mea

Pr.59 is available in the products manufactured in October 1995 or later. Therefore, it cannot be read from the products

No load current for each power supply voltage is as follows:- Approximately 15.5 A for 200 VAC 60 Hz- Approximately 21.7

You can use the following two methods:1. Turn ON MRS at the same time when STF turns OFF.2. Set Pr.10 = 60 Hz, Pr.11 = 0

By either of following methods: (MR-J4) 1. On MR Configurator2, select [Diagnosis] - [Alarm Display] - [Clear]. 2. Set

For the Instruction Manual "Applied", fill in the request sheet which is included in the last part of the Instruction Ma

You cannot remove the key sheet from products with the key sheet attached as a standard other than the PU operation type

You can switch between external operation and NET operation by turning ON/OFF the terminal X66 (RM). You can switch whil

Rapid blinking of the RUN LED indicates that the frequency setting command has not been input or the output stop signal

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

961-970 of Total 1353

prev 97 / 136page next

FR-SW3 CC-Link Seamless

From before, the QCPU has been used and each setting does not make a difference internally. Thus, the selection was reduced to the QCPU only. It can also be ... More Details >>
- No：20868
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Engineering Software
FR-A800-R2R

When the winding ratio is large, the control according to the winding diameter is required. The upper controller has measured the winding diameter and create... More Details >>
- No：20974
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800
FR-A024

Pr.59 is available in the products manufactured in October 1995 or later. Therefore, it cannot be read from the products manufactured before October 1995. More Details >>
- No：21170
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A024
No load current value of motor

No load current for each power supply voltage is as follows:- Approximately 15.5 A for 200 VAC 60 Hz- Approximately 21.7 A for 220 VAC 60 HzThe current is es... More Details >>
- No：21534
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Others
How can I have the motor coast to stop?

You can use the following two methods:1. Turn ON MRS at the same time when STF turns OFF.2. Set Pr.10 = 60 Hz, Pr.11 = 0 sec, and Pr.12 = 0% (when the invert... More Details >>
- No：21967
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Clearing the alarm history

By either of following methods: (MR-J4) 1. On MR Configurator2, select [Diagnosis] - [Alarm Display] - [Clear]. 2. Set alarm history clear of parameter to "... More Details >>
- No：23650
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4
Instruction manual

For the Instruction Manual "Applied", fill in the request sheet which is included in the last part of the Instruction Manual "Basic", and fax it to the speci... More Details >>
- No：21341
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Key sheet

You cannot remove the key sheet from products with the key sheet attached as a standard other than the PU operation type. When using the parameter unit FR-PU... More Details >>
- No：21596
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-U100
Switching between external operation and NET operation

You can switch between external operation and NET operation by turning ON/OFF the terminal X66 (RM). You can switch while Pr.79 (Operation mode) is set to "6... More Details >>
- No：21688
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Operation mode setting

Rapid blinking of the RUN LED indicates that the frequency setting command has not been input or the output stop signal has been input.Since Pr.79 is set to ... More Details >>
- No：21853
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

961-970 of Total 1353

Inquiries

page top