Connect the high power factor converter and inverter directly with a control cable, without using a relay. Since a fast-

Yes, you can set all of the three relay contacts to fault contacts.Set Pr.320 (RA1 output selection), 321 (RA2 output se

This subroutine is to check the data link status and needs to be executed only once at the start of the program.

The error LED on the master side of the programmable controller blinks (faulty station present).According to the SW80 st

Check if the CC-Link wires are short-circuited and/or station numbers are duplicated.

You can switch between the NET mode and external operation.Assign the X66 signal (Operation switching) to an unused term

It is not possible because the RS-485 terminal block is not installed. Use the FR-A800 (RS-485 communication type) when

Save the parameter file (.rpm) after reading the system file (.mel) created in SW1. With the saved parameter file (.rpm)

No. You cannot check the accumulated number of rotations on the monitor.

Pr.338 is for the communication operation command source at communication operation and specifies the command source to

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

971-980 of Total 1353

prev 98 / 136page next

Control cable between high power factor converter and inverter

Connect the high power factor converter and inverter directly with a control cable, without using a relay. Since a fast-response is required to shut off the ... More Details >>
- No：21555
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
FR-A7AR E kit (Relay output function)

Yes, you can set all of the three relay contacts to fault contacts.Set Pr.320 (RA1 output selection), 321 (RA2 output selection), and 322 (RA3 output selecti... More Details >>
- No：21712
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Program command

This subroutine is to check the data link status and needs to be executed only once at the start of the program. More Details >>
- No：21767
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Programmable controller

The error LED on the master side of the programmable controller blinks (faulty station present).According to the SW80 station information, an error flag is a... More Details >>
- No：21813
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
CC-Link

Check if the CC-Link wires are short-circuited and/or station numbers are duplicated.　　 More Details >>
- No：21891
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
NET mode, external operation switching

You can switch between the NET mode and external operation.Assign the X66 signal (Operation switching) to an unused terminal for switching.Also, set Pr.79 (O... More Details >>
- No：21906
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
FR-A800-E

It is not possible because the RS-485 terminal block is not installed. Use the FR-A800 (RS-485 communication type) when performing the RS-485 communication. More Details >>
- No：20881
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-A800 , FREQROL-F800
FR Configurator

Save the parameter file (.rpm) after reading the system file (.mel) created in SW1. With the saved parameter file (.rpm), the parameter of the 700 series can... More Details >>
- No：21141
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Engineering Software
Monitor indicator

No. You cannot check the accumulated number of rotations on the monitor.　　 More Details >>
- No：21715
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Running frequency setting

Pr.338 is for the communication operation command source at communication operation and specifies the command source to supply the start signal.Pr.339 is for... More Details >>
- No：21880
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P

971-980 of Total 1353

Inquiries

page top