Under a 50% torque limit, if the commanded speed (50 Hz in your example) cannot be achieved without torque exceeding 50%

Noise filtering and harmonics suppression are different matters and you need to install the line noise filter (FR-BSF01)

The output voltage is approximately 300 VDC for the 200 V class and approximately 600 VDC for the 400 V class. The outp

The FR-A7NC is required. ("FR-A7NC-E kit" for the FR-E700 series. The FR-E700-NC CC-Link communication type does not req

The error LED on the master side of the programmable controller blinks (faulty station present).According to the SW80 st

The FR-DU07 cannot be used with the FR-E700, FR-D700, or FR-F700PJ.

You can use it with the 700 series inverters. Note that the installation method of the card differs for the FR-E700 seri

Your understanding about the AC and DC reactors is correct. For the harmonics suppression effect obtained by using both

Many geared motors cannot continuously operate at low speed (for example, slower than 6 Hz) due to grease viscosity.If t

Keep 1 cm or more of clearance for 3.7 K or smaller, and 5 cm or more for 5.5 K or larger.If the clearance is too small,

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

981-990 of Total 1368

prev 99 / 137page next

Operation under torque limit in the speed control mode

Under a 50% torque limit, if the commanded speed (50 Hz in your example) cannot be achieved without torque exceeding 50%, since the torque does not exceed th... More Details >>
- No：21483
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-V200
Noise filter

Noise filtering and harmonics suppression are different matters and you need to install the line noise filter (FR-BSF01) against noise and DCL (FR-BEL) again... More Details >>
- No：21548
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Output voltage

The output voltage is approximately 300 VDC for the 200 V class and approximately 600 VDC for the 400 V class. 　The output voltage fluctuates due to fluctuat... More Details >>
- No：21561
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
CC-Link

The FR-A7NC is required. ("FR-A7NC-E kit" for the FR-E700 series. The FR-E700-NC CC-Link communication type does not require an option.) More Details >>
- No：21668
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Programmable controller

The error LED on the master side of the programmable controller blinks (faulty station present).According to the SW80 station information, an error flag is a... More Details >>
- No：21813
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
FR-DU07

The FR-DU07 cannot be used with the FR-E700, FR-D700, or FR-F700PJ. More Details >>
- No：21854
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ
CC-Link

You can use it with the 700 series inverters. Note that the installation method of the card differs for the FR-E700 series and FR-A700/F700 series.If you hav... More Details >>
- No：21887
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Power factor improving reactor

Your understanding about the AC and DC reactors is correct. For the harmonics suppression effect obtained by using both types of reactors, refer to the table... More Details >>
- No：21994
- Release Date：2018/08/22 16:30
- Category： Options
Speed control range

Many geared motors cannot continuously operate at low speed (for example, slower than 6 Hz) due to grease viscosity.If the motor you are using is of this typ... More Details >>
- No：22028
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A024
Installation clearance of inverters

Keep 1 cm or more of clearance for 3.7 K or smaller, and 5 cm or more for 5.5 K or larger.If the clearance is too small, the cooling effect is lowered. Secur... More Details >>
- No：22046
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500

981-990 of Total 1368

Inquiries

page top