This function allows you to select the digital value to perform D/A conversion from the following three patterns dependi

Set "[PA04] Function selection A-1" to "_1_ _h: Invalid".(Note): When using Q17nCPUN, set "Servo amplifier parameter 23

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("

The input/output cables used in the FX3GC and FX3UC basic units can be diverted to the FX5UC CPU Module (connector type)

N:N Network, Parallel Link, MC protocol, Non-protocol communication, MELSOFT connection, MODBUS RTU, and Predefined prot

No, the operation speed is not changed by changing the indirectly specified value.To change the speed during operation,

The keyword protection cannot be forcibly reset. Since only the keyword that has been registered by the user is accepta

Both OUT and SET instructions set the device by completion of condition.However, if not completion of condition, OUT ins

GX Works3 provides various intuitive features such as graphic-based system configuration and an extensive module librar

The default IP address (factory default value) of FX5 CPU modules is 192.168.3.250.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Automation Controllers MELSEC(28)

MELSEC MX Controller MX-R Model
MELSEC MX Controller MX-F Model(28)
MELSEC MX Controller Engineering Software
Programmable Controllers MELSEC(1702)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(643)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)

Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

1061-1070 of Total 1110

prev 107 / 111page next

Regarding the HOLD/CLEAR function of the built-in analog output

This function allows you to select the digital value to perform D/A conversion from the following three patterns depending on the operating status of the CPU... More Details >>
- No：39289
- Release Date：2023/01/12 16:51
- Category： MELSEC iQ-F Series , CPU Module , Analog
Servo amplifier forced stop

Set "[PA04] Function selection A-1" to "_1_ _h: Invalid".(Note): When using Q17nCPUN, set "Servo amplifier parameter 23 (Optional function 1)"... More Details >>
- No：23567
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
HPR request flag

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("[Md.31] Status": b3) turns ON or not.... More Details >>
- No：23618
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC
Regarding using the connector of the CPU Module

The input/output cables used in the FX3GC and FX3UC basic units can be diverted to the FX5UC CPU Module (connector type). More Details >>
- No：44350
- Release Date：2024/03/27 15:44
- Category： MELSEC iQ-F Series , CPU Module
Regarding communication supported by built-in RS-485 port

N:N Network, Parallel Link, MC protocol, Non-protocol communication, MELSOFT connection, MODBUS RTU, and Predefined protocol support are available. More Details >>
- No：22322
- Release Date：2018/08/30 13:55
- Update：2022/12/22 10:16
- Category： MELSEC iQ-F Series , CPU Module , Network/Communication
Speed change

No, the operation speed is not changed by changing the indirectly specified value.To change the speed during operation, use CHGV instruction. More Details >>
- No：23555
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Keyword protection of the MELSEC-F series

The keyword protection cannot be forcibly reset. Since only the keyword that has been registered by theuser is acceptable, please take measures to ensure th... More Details >>
- No：24784
- Release Date：2019/02/27 16:27
- Category： MELSEC-F Series , Engineering Software , Main Unit
OUT instruction

Both OUT and SET instructions set the device by completion of condition.However, if not completion of condition, OUT instruction resets the device while SET ... More Details >>
- No：23553
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Differences between GX Works3 and GX Works2

GX Works3 provides various intuitive features such as graphic-based system configuration and an extensive module library (module label/FB) as standard. You... More Details >>
- No：22489
- Release Date：2018/09/03 17:28
- Update：2018/09/20 09:43
- Category： MELSEC iQ-R Series
Regarding the default IP address

The default IP address (factory default value) of FX5CPU modules is 192.168.3.250. More Details >>
- No：22290
- Release Date：2018/08/30 13:55
- Update：2022/12/22 08:33
- Category： MELSEC iQ-F Series , CPU Module , Network/Communication

1061-1070 of Total 1110

Inquiries

page top