In the TCP/IP connection, you can connect up to 17 MELSOFT products at the same time using a dedicated connection for sy

You can set the parameters of the FL-net interface module with the data operation of the intelligent function module. Fo

A comparison result is held even after the command input turns off. The remaining comparison result can be cleared by us

LD instruction: 0.35 μs, MOV instruction: 0.779 μs. For other instructions, see the manual below. MELSEC iQ-F FX5 Progr

There are three QoS levels and FX5-ENET is also supported. ・QoS0 - The message is sent only once from the source clien

The cable cannot be used because the connector shape is different, so change the wiring. FX5-2HC/ES is a spring clamp te

An input and output use a single I/O number. (This is the same as QH42P.) When you replace a module that uses serial I/O

Select [Project] -> [Export to GX Developer Format File] and save the project so that it can be opened in GX Develope

The following Diatrend cable can be used.- DQ-U2

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Automation Controllers MELSEC(28)

MELSEC MX Controller MX-R Model
MELSEC MX Controller MX-F Model(28)
MELSEC MX Controller Engineering Software
Programmable Controllers MELSEC(1731)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)

Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

481-490 of Total 1123

prev 49 / 113page next

Limitation on the number of MELSOFT products that can be connected with the QJ71E71

In the TCP/IP connection, you can connect up to 17 MELSOFT products at the same time using a dedicated connection for system and the connections for users 1 ... More Details >>
- No：23063
- Release Date：2018/09/03 17:31
- Category： Network related products
FL-net setting of GX Works2

You can set the parameters of the FL-net interface module with the data operation of the intelligent function module. For details and operation procedure of... More Details >>
- No：23084
- Release Date：2018/09/03 17:31
- Update：2018/09/26 13:19
- Category： Network related products
Comparison result of the CMP instruction

A comparison result is held even after the command input turns off. The remaining comparison result can be cleared by using the RST or ZRST instruction. More Details >>
- No：24692
- Release Date：2019/02/27 08:56
- Category： MELSEC-F Series
Regarding Edge Relay

Not supported. More Details >>
- No：39305
- Release Date：2023/02/13 16:41
- Category： MELSEC iQ-F Series , CPU Module
Regarding Instruction processing time when the program capacity: 128 K steps are set

LD instruction: 0.35 μs, MOV instruction: 0.779 μs. For other instructions, see the manual below. MELSEC iQ-F FX5 Programming Manual (Instructions, Standa... More Details >>
- No：39362
- Release Date：2023/01/12 17:12
- Category： MELSEC iQ-F Series , CPU Module
Regarding the QoS function of the MQTT Communication function

There are three QoS levels and FX5-ENET is also supported. ・QoS0 - The message is sent only once from the source client. 　　　　　　Messages are not guarant... More Details >>
- No：40056
- Release Date：2023/08/25 09:04
- Category： MELSEC iQ-F Series , Network/Communication
Regarding cable diversion to FX5-2HC/ES

The cable cannot be used because the connector shape is different, so change the wiring. FX5-2HC/ES is a spring clamp terminal block, and FX3U-2HC is a MIL-... More Details >>
- No：44337
- Release Date：2024/03/20 13:26
- Category： MELSEC iQ-F Series , High-Speed Counter
I/O numbers of a MELSEC iQ-R series I/O combined module (RH42C4NT2P)

An input and output use a single I/O number. (This is the same as QH42P.) When you replace a module that uses serial I/O numbers (e.g. QX41Y41P) with this m... More Details >>
- No：22471
- Release Date：2018/09/03 17:28
- Update：2018/09/19 13:57
- Category： MELSEC iQ-R Series
How to read projects created by GX Works2 in GX Developer

Select [Project] -> [Export to GX Developer Format File] and save the project so that it can be opened in GX Developer.For more details, refer to GX Works... More Details >>
- No：22515
- Release Date：2018/09/03 17:28
- Category： MELSEC-Q Series
Cables for CPU modules

The following Diatrend cable can be used.- DQ-U2 More Details >>
- No：22623
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series

481-490 of Total 1123

Inquiries

page top