Yes. You can check the servo status through the following monitor data. • "[Md.108] Servo status 1" • "[Md.125] Servo

Select [Project] -> [Security] -> [User Management] from the menu to display the "User Addition" window.Set "User

The FX5 CPU module does not support EtherCAT communication. There are no products in the FX series or iQ-F series that

There are two ways to start a positioning operation: (1) Set the "[Cd.3] Positioning start No.", and turn ON the positio

No, the speed limit cannot be changed during operation.

The rapid stop deceleration time of parameter block is applied.However, when the rapid stop deceleration time is set in

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the chang

The error code "2100" is "SP.UNIT LAY ERR.". This error may be caused by one of the following factors. (1) In the I/

Both OUT and SET instructions set the device by completion of condition.However, if not completion of condition, OUT ins

The IP address can be changed from a program by using the IP address change function. The IP address change function ca

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Automation Controllers MELSEC(26)

MELSEC MX Controller MX-R Model
MELSEC MX Controller MX-F Model(26)
MELSEC MX Controller Engineering Software
Programmable Controllers MELSEC(1702)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(643)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)

Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

41-50 of Total 1108

prev 5 / 111page next

Servo status

Yes. You can check the servo status through the following monitor data. • "[Md.108] Servo status 1" • "[Md.125] Servo status 3" (QD77MS, LD77MS, LD77MH) ... More Details >>
- No：23588
- Release Date：2018/09/14 15:09
- Update：2023/03/09 10:02
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Setting passwords by project

Select [Project] -> [Security] -> [User Management] from the menu to display the "User Addition" window.Set "User Name", "Access Level", "Password", an... More Details >>
- No：22871
- Release Date：2018/09/03 17:30
- Category： Engineering Software
Regarding EtherCAT Communications

The FX5 CPU module does not support EtherCAT communication. There are no products in the FX series or iQ-F series that support EtherCAT communication. More Details >>
- No：39313
- Release Date：2023/02/14 08:54
- Category： MELSEC iQ-F Series , CPU Module , Network/Communication
Positioning start

There are two ways to start a positioning operation: (1) Set the "[Cd.3] Positioning start No.", and turn ON the positioning start signal. (2) Use the dedica... More Details >>
- No：23593
- Release Date：2018/09/14 15:09
- Category： QD77MS , LD77MS , LD77MH , QD75MH , QD75M
Speed limit value change during operation

No, the speed limit cannot be changed during operation. More Details >>
- No：23571
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Rapid stop signal

The rapid stop deceleration time of parameter block is applied.However, when the rapid stop deceleration time is set in the servo program, the value is enabl... More Details >>
- No：23557
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Speed limit value

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the change. More Details >>
- No：23556
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Error code "2100" in QCPU

The error code "2100" is "SP.UNIT LAY ERR.". This error may be caused by one of the following factors. (1) In the I/O assignment setting of the PLC parame... More Details >>
- No：22650
- Release Date：2018/09/03 17:29
- Update：2018/09/21 11:47
- Category： MELSEC-Q Series
OUT instruction

Both OUT and SET instructions set the device by completion of condition.However, if not completion of condition, OUT instruction resets the device while SET ... More Details >>
- No：23553
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Regarding how to change the IP address

The IP address can be changed from a program by using the IP address change function. The IP address change function can change the IP address, subnet mask,... More Details >>
- No：39332
- Release Date：2023/02/14 09:09
- Update：2024/08/19 09:52
- Category： MELSEC iQ-F Series , CPU Module , Network/Communication

41-50 of Total 1108

Inquiries

page top