Ver.1.10 is a standard where CC-Link station-to-station cable length restriction in Ver. 1.00 has been removed, and the

Executing the CPRTCL instruction (dedicated instruction) executes a specified protocol.

Check the following signals.- Module error signal : X0- Host data link status signal: X1- Other station data link s

The data link status is stored in SW80 to SW83.Each bit corresponds to a station number and a bit turns ON if the corres

A comparison result is held even after the command input turns off. The remaining comparison result can be cleared by us

Each special function unit/block has 8 occupied points, except for some special function devices. These 8 points do not

Whether the positioning parameter is used or the extension positioning parameter is used can be selected in BFM#32 (posi

Since the FX3U-ENET-ADP can be connected directly to the FX3GC series, optional equipment is not required. * When the

Yes, it's connected internally.

SD Memory Card module: You will need an FX5-SDCD and an SD memory card.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Automation Controllers MELSEC(28)

MELSEC MX Controller MX-R Model
MELSEC MX Controller MX-F Model(28)
MELSEC MX Controller Engineering Software
Programmable Controllers MELSEC(1731)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)

Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

551-560 of Total 1123

prev 56 / 113page next

Difference in specifications between CC-Link versions

Ver.1.10 is a standard where CC-Link station-to-station cable length restriction in Ver. 1.00 has been removed, and the length of all station-to-station cabl... More Details >>
- No：22975
- Release Date：2018/09/03 17:31
- Category： Network related products
Executing the QJ71C24N's pre-defined protocol support function

Executing the CPRTCL instruction (dedicated instruction) executes a specified protocol. More Details >>
- No：23004
- Release Date：2018/09/03 17:31
- Category： Network related products
CC-Link signals checked when an error occurs

Check the following signals.- Module error signal : X0- Host data link status signal: X1- Other station data link status signal: X3 More Details >>
- No：23021
- Release Date：2018/09/03 17:31
- Category： Network related products
How to check link errors in CC-Link slave stations

The data link status is stored in SW80 to SW83.Each bit corresponds to a station number and a bit turns ON if the corresponding station causes a data link er... More Details >>
- No：23031
- Release Date：2018/09/03 17:31
- Category： Network related products
Comparison result of the CMP instruction

A comparison result is held even after the command input turns off. The remaining comparison result can be cleared by using the RST or ZRST instruction. More Details >>
- No：24692
- Release Date：2019/02/27 08:56
- Category： MELSEC-F Series
Number of occupied points of special function devices

Each special function unit/block has 8 occupied points, except for some special function devices. These 8 points do not occupy 8 points of the actual I/O n... More Details >>
- No：24873
- Release Date：2019/04/15 08:06
- Category： MELSEC-F Series , Main Unit
Parameter setting of FX3U-1PG

Whether the positioning parameter is used or the extension positioning parameter is used can be selected in BFM#32 (positioning parameter selection). Select ... More Details >>
- No：24917
- Release Date：2019/04/17 11:40
- Category： MELSEC-F Series , Positioning Control
Connection of the FX3GC series and FX3U-ENET-ADP

Since the FX3U-ENET-ADP can be connected directly to the FX3GC series, optional equipment is not required. 　 * When the FX3U-ENET-ADP is used with other spe... More Details >>
- No：24976
- Release Date：2019/04/23 07:20
- Category： MELSEC-F Series , Main Unit , Network/Communication
Regarding the COM terminal of the multiple input module

Yes, it's connected internally. More Details >>
- No：39318
- Release Date：2023/01/12 16:54
- Category： MELSEC iQ-F Series , Analog
Regarding using the FX5S CPU module Data Logging Function

SD Memory Card module: You will need an FX5-SDCD and an SD memory card. More Details >>
- No：39333
- Release Date：2023/02/14 09:09
- Category： MELSEC iQ-F Series , Option , CPU Module

551-560 of Total 1123

Inquiries

page top