The FR-E700 is not supported by FR-SW2-SETUP-WJ. The FR-E700 series are supported by FR-SW3-SETUP-WJ. This software can

The inverter has the calibration function.Use Pr.125 (Terminal 2 frequency setting gain frequency) and Pr.C4 (Terminal 2

Yes.Set Pr.19 (Base frequency voltage) to "200 V".200 V output will be obtained during 60 Hz operation.

When using multiple motors, connect an external thermal for each of them. Set Pr.9 to "0" to disable the function. (When

You can change the terminal 4 to voltage input. (The terminal 4 is set to the current input terminal at the initial sett

There is no problem with the wiring. Keep the rating (24 VDC, 0.1 A) of the terminal PC.

It is not recommended to start and stop the inverter with the electromagnetic contactor (MC). This will accelerate the d

Even after setting Pr.340 to "10", the change is reflected after resetting the power supply.Perform the power reset.Sinc

You can write frequency setting by setting Pr.339 (Communication speed command source) to "0".

Assign X16 signal, and set Pr.79 to "0", to switch the operation mode with turning ON/OFF X16 signal.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E700 ]

41-50 of Total 393

prev 5 / 40page next

Supported model for FR-Configurator

The FR-E700 is not supported by FR-SW2-SETUP-WJ. The FR-E700 series are supported by FR-SW3-SETUP-WJ. This software can be downloaded from the Mitsubishi Ele... More Details >>
- No：21314
- Release Date：2018/08/22 16:26
External operation

The inverter has the calibration function.Use Pr.125 (Terminal 2 frequency setting gain frequency) and Pr.C4 (Terminal 2 frequency setting gain) for calibrat... More Details >>
- No：21849
- Release Date：2018/08/22 16:29
Motor specifications setting

Yes.Set Pr.19 (Base frequency voltage) to "200 V".200 V output will be obtained during 60 Hz operation. More Details >>
- No：21717
- Release Date：2018/08/22 16:29
Electronic thermal O/L relay setting

When using multiple motors, connect an external thermal for each of them. Set Pr.9 to "0" to disable the function. (When multiple motors are present, it is n... More Details >>
- No：21676
- Release Date：2018/08/22 16:28
Frequency setting

You can change the terminal 4 to voltage input. (The terminal 4 is set to the current input terminal at the initial setting.)To change the terminal 4 to volt... More Details >>
- No：21787
- Release Date：2018/08/22 16:29
Wiring the terminal

There is no problem with the wiring. Keep the rating (24 VDC, 0.1 A) of the terminal PC. More Details >>
- No：21342
- Release Date：2018/08/22 16:27
Electromagnetic contactor

It is not recommended to start and stop the inverter with the electromagnetic contactor (MC). This will accelerate the deterioration (due to the inrush curre... More Details >>
- No：21322
- Release Date：2018/08/22 16:27
Switching between PU and NET operations

Even after setting Pr.340 to "10", the change is reflected after resetting the power supply.Perform the power reset.Since changes to the communication parame... More Details >>
- No：21696
- Release Date：2018/08/22 16:28
Switching between external operation and NET operation

You can write frequency setting by setting Pr.339 (Communication speed command source) to "0". More Details >>
- No：21687
- Release Date：2018/08/22 16:28
Switching between External operation mode and PU operation mode

Assign X16 signal, and set Pr.79 to "0", to switch the operation mode with turning ON/OFF X16 signal. More Details >>
- No：21288
- Release Date：2018/08/22 16:26

41-50 of Total 393

Inquiries

page top