Check that Pr.3 (Base frequency) is set to "200 Hz". Adjust Pr.0 (Torque boost) as necessary.

Set Pr.340 (Communication startup mode selection) to "10".The operation mode can be switched between PU and NET by assig

The multi-speed setting is prioritized.The external potentiometer setting is effective when the multi-speed signal is no

When turning the setting dial to set the frequency, press the "SET" key while the desired value blinks. (The setting fre

You can write frequency setting by setting Pr.339 (Communication speed command source) to "0".

It depends on the setting of Pr.79 (Operation mode).Pr.79 can be set to "2" or "3".If Pr.79 is "2", it is judged that th

Considering voltage drop of the internal power supply and influence by noise, the wiring length should be 30 m or less.

This is because the protective function works to stop the motor. It is not a fault indication.To cancel the protective f

This parameter cannot be changed in the external operation mode.Change Pr.77 (Parameter write selection) to "2" before c

When using multiple motors, connect an external thermal for each of them. Set Pr.9 to "0" to disable the function. (When

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700 ]

61-70 of Total 296

prev 7 / 30page next

Rated frequency setting

Check that Pr.3 (Base frequency) is set to "200 Hz". Adjust Pr.0 (Torque boost) as necessary. More Details >>
- No：21280
- Release Date：2018/08/22 16:26
Switching between PU and NET operation modes

Set Pr.340 (Communication startup mode selection) to "10".The operation mode can be switched between PU and NET by assigning X65 (PU-NET operation switching)... More Details >>
- No：21878
- Release Date：2018/08/22 16:29
Multi-speed setting and external potentiometer

The multi-speed setting is prioritized.The external potentiometer setting is effective when the multi-speed signal is not input. More Details >>
- No：21773
- Release Date：2018/08/22 16:29
Frequency setting

When turning the setting dial to set the frequency, press the "SET" key while the desired value blinks. (The setting frequency and "F" flicker alternately.) More Details >>
- No：21742
- Release Date：2018/08/22 16:29
Switching between external operation and NET operation

You can write frequency setting by setting Pr.339 (Communication speed command source) to "0". More Details >>
- No：21687
- Release Date：2018/08/22 16:28
External multi-speed setting and multi-speed command

It depends on the setting of Pr.79 (Operation mode).Pr.79 can be set to "2" or "3".If Pr.79 is "2", it is judged that the multi-speed frequency command was s... More Details >>
- No：21815
- Release Date：2018/08/22 16:29
Frequency manual controller FR-AX

Considering voltage drop of the internal power supply and influence by noise, the wiring length should be 30 m or less. More Details >>
- No：21809
- Release Date：2018/08/22 16:29
Operation panel

This is because the protective function works to stop the motor. It is not a fault indication.To cancel the protective function, turn OFF the start signal an... More Details >>
- No：21775
- Release Date：2018/08/22 16:29
Frequency setting

This parameter cannot be changed in the external operation mode.Change Pr.77 (Parameter write selection) to "2" before changing the setting of Pr.72. More Details >>
- No：21743
- Release Date：2018/08/22 16:29
Electronic thermal O/L relay setting

When using multiple motors, connect an external thermal for each of them. Set Pr.9 to "0" to disable the function. (When multiple motors are present, it is n... More Details >>
- No：21676
- Release Date：2018/08/22 16:28

61-70 of Total 296

Inquiries

page top