It is the standardized Mini-B connector.

Check the version of FR-Configurator (FR-SW3-SETUP-WJ). If the version is "1.00", it does not support or detect the FR-E

Set Pr.338 (Communication command source) to "0" to give a start command from "NET". Set Pr.339 (Speed command source) t

Set Pr.340 (Communication startup mode selection) to other than "0".Also, set Pr.79 (Operation mode) to "0", "2", or "6"

Press the "SET" key once while the output frequency is monitored.The unit indicator LED changes from "Hz" to "A" and the

You also need to set Pr.57 (Restart coasting time).The function does not work just by setting Pr.162 unless setting this

Turning ON/OFF the output side during operation causes open/close surges that may trigger the protective function (again

It cannot be avoided by using parameters.

Use Pr.903 (Frequency setting voltage gain) for setting the FR-E500. For the 700 series, use Pr.125 (Terminal 2 frequenc

You can monitor the fault output in both NET operation and external operation.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700P

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700P ]

81-90 of Total 295

prev 9 / 30page next

Connection cable of FR-Configurator

It is the standardized Mini-B connector. More Details >>
- No：21312
- Release Date：2018/08/22 16:26
Model setting in FR-Configurator

Check the version of FR-Configurator (FR-SW3-SETUP-WJ). If the version is "1.00", it does not support or detect the FR-E740. Version "2.00" supports the FR-E... More Details >>
- No：21309
- Release Date：2018/08/22 16:26
Start command

Set Pr.338 (Communication command source) to "0" to give a start command from "NET". Set Pr.339 (Speed command source) to "1" to make a frequency setting fro... More Details >>
- No：21285
- Release Date：2018/08/22 16:26
CC-Link

Set Pr.340 (Communication startup mode selection) to other than "0".Also, set Pr.79 (Operation mode) to "0", "2", or "6".Powering the inverter on automatical... More Details >>
- No：21903
- Release Date：2018/08/22 16:30
Monitor indicator

Press the "SET" key once while the output frequency is monitored.The unit indicator LED changes from "Hz" to "A" and the monitor display changes to the current. More Details >>
- No：21764
- Release Date：2018/08/22 16:29
Automatic restart after instantaneous power failure setting

You also need to set Pr.57 (Restart coasting time).The function does not work just by setting Pr.162 unless setting this parameter.(For A700, F700, and F700P... More Details >>
- No：21731
- Release Date：2018/08/22 16:29
Electromagnetic contactor

Turning ON/OFF the output side during operation causes open/close surges that may trigger the protective function (against overcurrent or overvoltage) of the... More Details >>
- No：21725
- Release Date：2018/08/22 16:29
Electromagnetic contactor

It cannot be avoided by using parameters.　　 More Details >>
- No：21724
- Release Date：2018/08/22 16:29
Adjustment of analog gain

Use Pr.903 (Frequency setting voltage gain) for setting the FR-E500. For the 700 series, use Pr.125 (Terminal 2 frequency setting gain frequency) and Pr.C4 (... More Details >>
- No：21689
- Release Date：2018/08/22 16:28
Switching between external operation and NET operation

You can monitor the fault output in both NET operation and external operation. More Details >>
- No：21686
- Release Date：2018/08/22 16:28

81-90 of Total 295

Inquiries

page top